Models > 11070956990 > Instructions

11070956990 Kenmore Dryer - Instructions

All Instructions for the 11070956990
406 - 420 of 615
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
couldnt find this model dryer on the whirpool part on their site
Found this part on your site very EZ bought it you shipped to my door got it when you said it would be here open it installed it propblem over glad i found you guys will use again Very good website Keep up the good work THANK YOU
Parts Used:
Lint Filter
  • clyde from Harrisburg, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
latch inside door popped out
Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min
Parts Used:
Door Catch Kit
  • zachery from snoqualmie, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer cycles but will not heat
removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.
Parts Used:
M Series New Style Coil Kit
  • daniel from mercedes, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Switch broken
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.
Parts Used:
Lid Switch
  • Willie from Virginia Beach, VA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
No flame
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Parts Used:
M Series New Style Coil Kit
  • Rafael from SAINT PAUL, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Old lint filter had holes in it.
removed old one installed new one.
Parts Used:
Lint Filter
  • John from Massanutten, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No heat to dryer
The dryer is a Whirlpool Duet,Model GGW9200LW0. My wife said, the dryer was not heating. I never repaired a dryer before, so I went online to get some ideas about what to expect. I saw the web site for PartSelect.com,typed in the model number and the part drawings and hints to repair along with vedios to help me guide with the repair. Now I removed the top cover from the dryer and on the right was a ziplock bag which contained the technical info about the dryer. With the tech info and hints from PartSelect I selected the parts. Because the weekend was two days away I received the parts on Monday. On Tuesday, I started to work on the dryer, first I removed the front and rear panels vacuumed the inside, located where the parts went, changed the parts, one-at-a time. Put on the back panel, gas line, and exhaust hose, and put electric plug in. Started the dryer and walla, the dryer started, the gas burner came on. All parts fit and no problems, Thank You PartSelect.
Parts Used:
Thermal Cut-Off Fuse Kit Thermostat, Internal-Bias Disposable Thermal Fuse - Two Terminal Igniter Kit
  • Eugene from Manchester, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
No heat
Just like the instructions. Piece of cake.
Parts Used:
Igniter Kit
  • Randal from Fowlerville, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer wasn't heating
Followed the parts select You tube video. Was helpful. Note the Ignitor kit is very sensitive. We didn't need an ignitor right now but purchased one in case the other 2 parts didn't help the problem. We took the ignitor ( wrapped in a bag) out of the packaging and it snapped in half without even touching the sensitive end. Note handle with extreme care.
Parts Used:
Dryer Radiant Flame Sensor M Series New Style Coil Kit
  • ERIN from RED WING, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer was throwing a E1 Error
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).
Parts Used:
Thermostat, Internal-Bias
  • John from Indian land, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Door latch was broken
This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.
Parts Used:
Door Catch Kit
  • William from Champaign, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door would not close
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.
Parts Used:
Door Catch Kit
  • Daniel from Stratford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer doesn't complete it's cycle
Removal of the back panel was easy - 9 screws - replaced both the thermistor and the two-terminal thermal fuse - put back panel on - supplied power - tested it - works like a champ.
Parts Used:
Thermostat, Internal-Bias Disposable Thermal Fuse - Two Terminal
  • MICHAEL from PHOENIX, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Felt wears on the dryer lint screen
No repair. Just replaced the screens in the dryer and they slide in and out to clean. The felt gets worn fast.
Parts Used:
Lint Filter
  • Judy from Cloverdale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Washer quit running when lid was closed
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.
Parts Used:
Lid Switch
  • Colleen from Indianapolis, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11070956990
406 - 420 of 615
Back to Top