11070722990 Kenmore Dryer - Instructions

Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.

Thermal Fuse & Cycling Thermostat put it in like 321 was done.

Replaced igniter

I got great advice and the know how form other's instructions. It was a really easy fix. I unplugged the dryer and turned off the gas valve. Open up the dryer by taking out the two screws securing the lint screen. Then pop off the top of the dryer by inserting a screwdriver. Disconnect the door switch and depending on model remove the two screws or bolts that keep the front panel attached. Careful, on my dryer once took the front panel off the drum fell forward. I kept it in place by wedging a small cardboard box under it. Unplug the two wires going into each of the coils. Remember which one goes where(2 prong vs 3 prong). Undue the two screws holding the bracket to the coils and remove bracket and bad coils. Put the new coils in, attach wires and bracket. Put dryer back together. Make sure to remember to plug back in door switch. I forgot and when I tried to test it wouldn't work and it got me worried that I broke it or something.

I first came to the internet to resolve what was wrong. After finding the video I thought was correct I started. I used my volt/ohm meter to check the thermal fuse as instructed on the video and that was the problem. I ordered the new thermal fuse from PartSelect late in the day and it was in my hands the next evening. With in 20 minutes the dryer was doing what it was suppose to do. The hardest part was getting the back cover of the crier off and that wasn't to bad.

I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.

first I took a flat head screw driver to pop the top of the dryer open, and then removed the screws from the lint tray. Next I lifted the lip back making sure it was supported by the wall behind. Third I removed the front of the unit by removing the bolts attached on both ends of the top of the unit. I then opened the door and removed the screws on the right top side of the lining of the door to the switch. Then I carefully held onto the tub while lifting the front face of the unit to remove the face of the dryer. After carefully removing the face I released the tub and set it aside. Then I picked up the tension pulley set it back in its slot followed by placing the belt rib side down around the tub. Next step was to place the tub back in the unit making sure the felt was in place and then I ran the belt back through the tension pulley applying tension in order to get the belt back onto the motor making sure the ribs of the belt aligned up with the ribs on the motors belt drive wheel. After completing that I then grabbed the front panel of the dryer unit and gently replaced the panel making sure that the slots and hooks lined up while placing the tub back in alignment of front panel. Once that was complete I replaced the screws in the door switch followed by replacing the bolts in the inside of the top comer of the front panel till hand tight. Last but not least I slid the lint tray back in place in order to make sure screws did not fall in to the hole the lint tray occupies. After replacing the screws I then plugged in the dryer gave the tub a few spins with my hand to make sure it was in place correctly I gave it a test drive by leaving the door open and pressing the door switch shutting off the light in the unit so it since the door was shut and turn the unit on for a cycle for at least one minute to see if the tub rolled freely on its own. All was good and only took 12 minutes to change and replace part. Easley can be done by any DIY first timers. Me I work with all kinds of units but the older units are easy and no need for a tech I promise.

Repaired as per instructions via e mail. No problems encountered.

Got the info from PartSelect that the door switch might be the problem, which confirmed my suspicions (as the dryer had lately been failing to stop when the door was opened), ordered the door switch (which had arrived in good time, BTW), installed the part after figuring out that the top panel of the dryer is fixed in place with the two screws accessible in the filter door opening. Put it all back together (that is, re-fixed the top panel with the two screws I'd had to remove), plugged it in, fired it up, ascertained that the repair had been successful, expressed appropriate thankfulness to God for an easier-than-imagined repair, cracked a celebratory brewed product, and commenced working through a hefty few piles of neglected laundry.

After I watched the video I read other people's repairs and used both to get the belt changed.The dryer is old, I believe it is from the 70's. We took the front off and then laid the dryer on its back for easier access, looped the belt as described on the video, turned the drum counter clock-wise and then reattached the front. It was very simple thanks to the video and other people's suggestions. Dryer works great and very happy it turned out to be an easy fix.

It took me nearly 3 hrs. but I don't do this for a living. Your instruction video was most helpful, madeit easy to know what to do & how to repair dryer. Part Select is top on my list. The site is easy to use & tells you what to replace based on the problem you are experiencing. The instinctual video are the best in the BUZ! Many thanks for making difficult repair much easier. David

My dryer started staying on when I opened the door to check the clothes, which I adapted to. Over the next few weeks, the dryer would not start at all. The website was very helpful in determining the possible parts needed to make the repair. The video shown was spot on and very helpful with its instructions on access to the part and replacing the part. The most time it took for me was cleaning behind the dryer and trying to remove the existing switch. I kept trying to squeeze the tabs on each side to get it past the tab and that wasnt working for me. Finally I took a small flat screwdriver and gently lifted the plastic on the switch up over the tab and that allowed me to pull and remove the switch easily. The whole time from start to finish for me was 45 minutes. Not bad for a 50 year old lady :) I have to say that this whole process has giving me alot of confidence in making basic appiance repairs. I have my partsselect.com magnet proudly displayed on my dryer and will not hesitate to use them again in the future.

The dryer opens up pretty easily; there are two screws holding the lint filter housing to the top panel that must be removed before the top will come up. The top panel pops open by prying it up with a screw driver. Once it's off there are two screws inside near the top that hold the upper front panel to the sides. There are also two screws that need to be loosened, but not removed, at the very bottom of the upper front panel, accessed by removing the lower front panel which is also popped out by prying (the upper part of the lower panel is pulled straight out, and is held to the bottom of the unit by hinge-like clips). Once the upper front panel is wriggled back the drum will slump off but stay pretty much in place while you set the panel aside (it has an electrical lead that goes to the door-closed sensor, but if you pop its clips loose in a couple spots you'll have enough slack to set it to the side). The drum pulls off easily. You might want to take a photo of the belt/pulley arrangement underneath it before removing everything, as it is not intuitively obvious how the belt runs thru the pulleys. Once the drum is gone vacuum up all that accumulated lint, then pop off the metal clips that hold the motor on. I was surprised at how little holds that motor on; apparently it's enough. Here is where I ran into my one snag: I couldn't unscrew the blower wheel from the motor shaft, and you have to get that fan off to get the motor out. You're supposed to clamp a wrench on the plastic fan just inside the dryer housing, and unscrew it by turning the shaft from the other side. No go. I eventually drilled a sequence of holes into the plastic around the metal shaft (easy) and could pull the motor out, but of course now I needed a $20 fan replacement. The motor and fan showed up in 2-3 days. Unfortunately, the motor came with a pulley that needed a narrower drive belt than my original. I guess I could have cut the original down, but i just went ahead and ordered a new one ($12). Everything went back together surprisingly easily. Getting the new fan on was much easier than getting that old one off.

take two phillips srews out of lint catch frame. next take a screw driver pry up front top part on dryer.lean back top out of way.take two screws out of top of dryer door. disconnect electrical connection dryer door frame.and pull frame upward and off. you will see roller bracket with end made to put in slott. put it in first slott under belt motor.take belt and pull it through under roller and hook it with screwdriver to motor pulley.by putting the tip of screwdriver on motor pulley with belt on screwdriver and lift up until belt slides on to pulley. make sure you put belt around barrel. before putting belt through roller bracket and on to motor pulley.and use something to put under barrel so it will not get in the way and fall off.

I checked the site, diagnosis - need thermal fuse and it suggested replacing thermostat as well. Viewed the video. Removed dryer hose. Used a 1/4 hex socket to remove screws from back of dryer, removed the screw from thermal fuse pulled out the fuse; inserted the new ones wires to prongs and screwed it back in. I did the same thing with the cycling thermostat. Terrific while I was in there; vacuumed all the dust out. Screwed the back on, put the vent hose on. $36...Very Happy!!! Also, viewed their video to access drum. Fixed the floppy fin inside dryer and vacuumed arount drum as well! BTW....I am a 65 year old woman!!! A very happy one! The initial job was about 20 min...doing vacuuming and drum repair was a lot longer as I had to hunt down washers to put on one of the fins so it wouldn't keep moving. Cleaning the fin of debri and lining it up etc Total time: maybe an hour and a half. TIP: People should wash their lint filters at LEAST once a year! Helps prevent overheating and fires! Thank you Part Select! Linda :)