11068847700 Kenmore Dryer - Instructions

i still cant get it to start i keep having that 06 code revision after i ran the diagnostic i replace the thermistor right after that the dryer start but only dry one load and wont start again then i replace the thermal fuse still not working i order the door switch hopefully that might do it

Previous consumer help advised to check the Thermal Fuse. A quick check using an ohm meter or simply connecting the leads together, confirmed that the Fuse was open and bad. The other essential item is to clean & vacuum all lint from all other dryer parts on the top, drum & back of the dryer. Be sure to also perform a check of the Cycling Thermostat, located near the Thermo Fuse. This is not a difficult repair. Just be sure to disconnect the 220 V and the circuit breaker. A $9 fuse was better than the cost of a repairman or new dryer. Barry Burke, Cincinnati, Ohio.

My dryer is one of the energy efficient models (HE). The video for the installations was knowledgeable, but getting into the front of mine only required removing to screws from the bottom left & right corner (not using a putty knife to pop the springs). the plate on the front drops after that. Also when taking out the tube with the dryer element in it took a lot more twisting inside the frame to get it loose. Still turn it after the wire connections have been pulled off a little bit better than 1/4 of a turn. Also the heating element was in there really, really tight. It required tapping on the plate with a screw driver and a rubber hammer to take it out & put in (not that tough). After putting it in a 1/4 of a turn so that the tab was inside the blower tube. everything after that was pretty easy. The video showed this all being done in a clean dryer. It has been my experience that before all is running & closed back up that a vacuum or shop vac needs to go thru there to clean things up & prevent a future fire.

I put my mind into the repair based on what I saw for a problem and what was given for advise. I was steered toward the thermal fuse, ordered and installed it. Not repaired, in checking the power backward to the panel I found that the dedicated panel had one side blown still allowing for the motor to run but not the element. hmmm

I found some help on-line that suggested some of the most likely causes. The on-line videos showed how to remove clips/panels to access the parts. Once I found the possibly failed parts, door switch and thermal fuse, I did a quick continuity check and found that the thermal fuse had an open circuit.

Took off the backplate of dryer, replaced fuse, done.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

afer looking at the expoled views of the drier and locating the switch i checked to switch operation and found it wouldn't click.i ordered the switch,it arrived in just a couple days(right in the middle of the xmas holidays)i popped the top on the drier after finding 2 screws on the lint screen opening on top,2 screws mounted the switch,reassembled in reverse order and tested the drier.it was easy and with the new part in hand i saved aprox 200.00 dollars fixing it myself. p.s. please unplug the drier before starting any repairs...

First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.

Had a lot of trouble getting front panel off. Check You Tube for directions. Checked heating coils and thermostats and found they were OK. Cleaned lint from fan and replaced thermostats although they may not have needed it (thermal cut-off kit). Put panel back and it works. See YouTube to see how to check coil and thermostats. They may check but if something is wrong it is either them or the control board. Thermal Cut-Off Kit is much cheaper.

I watched the PartSelect video once before the part arrived. Had the part replaced in under 15 minutes. Very quick and easy.

Remove the exhaust tubing connection and the back panel (five nut screws). Locate the fuse; it is just to the right of the lint trap shoot, midway between the top and bottom of the back panel area. Replacement is visually intuitive.

I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.

Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.

I followed the directions on your site. I pulled out the filter on the top of the machine. Then removed the two screws where the filter is located, I am not sure I would have found those screws had it not been for your directions. I then pulled up on the top of the machine by grabbing the sides near the front of the top, it came right up. I then raised it enough to place a broom handle to hold the top up so I could reach the switch. I removed the two screws holding the switch and then pulled the connector apart. I then replaced the switch with the two screws and plugged the connector back together. Removed the broom handle and closed the top and replaced the two screws I removed by the filter. Replaced the filter and started the machine running and opened the door and it turned off and the light came on. It took me about twenty minutes.