Models > 11068822700 > Instructions

11068822700 Kenmore Dryer - Instructions

All Instructions for the 11068822700
931 - 940 of 940
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer Ran -No Heat
Watched video on locating and testing parts (did help that I had a digital meter w/cont-tone ) removed and cleaned out dryer cabinet tested heating element-was ok went to thermal cutoff (tested bad ) ordered kit from part select parts arrived within two days (fantastic ) replaced parts in thermal cut off kit . Replaced dryer back also and important -removed dryer vent and cleaned out pipe -replaced vent pipe turned on the power tried dryer works like new again your easy to follow instructions made this a very easy job thanks people ! You saved me a great deal of aggravation and more important money
Parts Used:
Thermal Cut-Off Kit
  • John from WEST CHESTER, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer would run, but not heat
Removed the back panel, found the fuse and replaced it. Easiest thing I've ever done! I was expecting it not to be the problem, but I started with the "most common" issue via the website. Voila...it was the problem!
Parts Used:
Dryer Thermal Fuse
  • Kenny from Euclid, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
Door Catch Kit
  • Charles from North Chesterfield, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Indicator lights blinking, not drying, auto settings not working
Unlike your video, with this model, the thermal fuse is located near the front of the dryer, which I didn't find out until the back was already off.
Parts Used:
Dryer Thermal Fuse
  • James from Frankfort, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer would not shut down when door is opened.
Follow your instructions. Thank You
Parts Used:
Dryer Door Switch
  • Robert from Garden Grove, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Heating element
1) Unplug the dryer. 2) Remove lower front panel, use screw driver to push down then pop the top forward. 3) Heating element is on the right. 1/4 inch nut driver removes front plate and the screws holding the foot in place.4) Remove the two wires connected to the heating element and pull the heater toward yourself 5) Remove the screw next to where the two wires connected to the heater, It takes some effort but it will slide out the heating element. Slide the new element in, put in screw next to terminals, slide heater back into place, put foot screws in, put deflector back on with screw, connect the wires back onto the heating element, put the front cover back on, plug in the dryer and test. It will smell for about a minute being new.
Parts Used:
Dryer Heating Element
  • Bryce from Golden, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
Door Catch Kit
  • George from Melbourne, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
Heating Element Connection Wire Kit
  • Betty from Erie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer just shut off and would not start
went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim
Parts Used:
Dryer Thermal Fuse
  • timothy from sheridan, WY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
First squeaking, then something happened and would not run.
Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!
Parts Used:
Idler Pulley
  • Ernie from AVONDALE, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11068822700
931 - 940 of 940
Back to Top