11068432700 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No heat from dryer to dry clothes
-
Juanita from Miami Gardens, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
The clothes dryer was making squeaky, screechy noises.
First off, I was somewhat misled by the website and ordered the wrong parts. I entered my model number and ordered the maintainance kit. The info said it was good for Whirlpool, Maytag and others. I also watched the video which is apparently the Whirlpool. So, the wrong parts arrived. The PartSelect peeple were very helpful in getting me the right parts and getting them delivered promptly. I then found the proper video, watched that and did the repair. Be aware that all models have subtle differences. Mine had two long screws in the bottom of the door frame not shown in the video. I also had a little trouble with the pulley spring. I removed the assembly and then got it all back together ok. Then I lost one of the door hinge screws. It evaporated. The replacement part was like $4 so I used one from the local HD and all is well.
Parts Used:
-
Michael from Baltimore, MD
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer was getting too hot.
I reviewed the on-line video (which was very good by the way) and read the instructions that came with the thermal cut-off kit. Replacement of the upper thermostat was a piece of cake, very straight-forward; just remove the old & replace with the new. The instructions for replacing the lower thermostat were a little confusing because my dryer did not have the orange wire coming from the wiring harness, but after looking carefully at the old thermostat and how it was connected, I finally figured out how the jumper wire was to be connected and successfully installed the lower unit. Bottom line...the dryer works like new. Much cheaper than calling the repairman! Thanks PartSelect!
Parts Used:
-
Kenneth from Shady Spring, WV
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Dryer was not getting hot enough to dry cloths in a single cycle
Unplug the dryer, take off the rear panel with a nut driver, remove the old heating element (3 screws). remove the thermostat attached to the element, put the thermostat on the new element and install the new element with old screws. re install the back panel with old screws and you are done. Plug it in and it's ready to go!
Parts Used:
-
Jacob from Greenfield, MO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The dryer would tumble but no heat.
I watched to replacement video from the website and followed. I did use the tip of a small knife to get the connector to come loose on the old switch. It was a really easy repair.
Parts Used:
-
Koleen from odon, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
low heat
removed back cover 9 screws , 2 screws on heating element and it pulled out ,3wiers and the new one went in. thermal fuse, was one screw and two wiers and I was done.
Parts Used:
-
charles from camden, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My dryer would not heat at all
After watching your instuctional video I removed the back plate removed old wired and unscrewed the part couldn't have been easier. I have never worked on a dryer in my life and am female :). The hardest part was turning off and unhooking the gas line and again after watching a video on how to do it all went well.
Parts Used:
-
Diane from Palm Desert, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat up.
I watched the repair expert on you tube. Went to my dryer and took out the heating element, inspected it, and found a broken element wire. Ordered a new element and since I was in there I also replaced the high limit thermostat. Parts select made it easy and my dryer works great again. Thank you.
Parts Used:
-
John from Quincy, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
fuse went bad
I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you
Parts Used:
-
Charles from WAYNESBURG, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Drive Belt
Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.
Parts Used:
-
Cosmo from Somerville, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drum still turns when door open and light does not come on.
1.Unplugged power cord to Dryer. 2.Removed Dryer vent screen, unscrewed two screws located in dryer vent.3.Pried open top of dryer using putty knife. 4.Propped up top of dryer using 6 inch piece of wood resting on drum of dryer. 5.Removed screw holding door switch.6.Removed door switch from harness using putty Knife to pry apart connection. 7. Installed new door switch to harness and re-installed. 8.Removed wood used to prop open top, closed top, re-installed all screws, dryer vent and plugged dryer back up.
Parts Used:
-
Leroy from New Orleans, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
push to start switch didnt work
-
LEE from BUTLER, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
drum not rotating
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.
Parts Used:
-
Robert G from Dansville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken belt and roller
-
FLOR from Jersey City, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
No heat
It took longest to take apart and test to see which part was bad. I had never done it before. Got it apart and used the drawings on Parts Select to find location of parts. Testing only few minutes found bad thermostat.Ordered parts, and they came in 1 1/2 days. I replaced both thermostats being they were in the kit. Actual repair took maybe 15 minutes. Vacuumed out everything I could. Took lint trap out a vacuumed. Put it back together, plugged it in, heated like new. All time told I would say little over hour.
Parts Used:
-
Gordon from Harpursville, NY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!