Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
1`) broken blower motor drive belt,2) blower moter drive belt pulley loosened & seperated from shaft
1) Unplugged unit & used the 5 in 1 tool to disengage top panel clips from top of front panel & tilted top panel up & out of the way, . 2) Disconnected electrical connection @ upper right of front panel, Used drill & 5/16" socket & adapter to remove 2 upper front panel screws on backside of panel & removed panel. 3) Removed 4 screws from lint screen duct, unplugged elect. con.@ the right & removed lint screen & duct from dryer bulkhead.. 4) Loosened 2 top screws & removed 2 bottom screws from bulkhead & lifted bulkhead up & out & set aside. 5) Slid drum belt off the back of the drum & removed the drum 6) Ceaned the blower moter drive shaft threads & threads inside the shaft pulley. Used a file to clean up any burrs on shaft pulley, coated treads of pulley & shaft with red lock tite thread dressing & re-instaled pulley back onto shaft with ajustable pliers while holding blower fan blades steady from inside the blower motor housing. with other hand. note: (pulley is left handed thread) 7) Looped new belt onto drive motor pulley then worked it back onto blower moter pulley with one hand while turning the blades of the blower from inside the blower housing with other hand until it was back in place & ribs on belt were seated in the mating ribs of the pulley. 8) Put everything back in reverse order with the exception of removing the back panel to reinstall the drum belt onto the drive motor shaft pulley and tensioner @ bottom left in back of the dryer.
Hope this instructional is able to help some one else & good luck with your projects!
On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the parts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start, showed F40 code
Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Dryer would run 1 min then stop running with some heat in drum
Videos are excellent to open and access internal parts. It turned out a rat was killed in the blower fan when we first encountered the problem. This prevented the blower from turning which interfered with motor function.
This required removing drum & belt, disconnecting motor clips, blower belt, and blower housing. The blower housing needed to be disassembled. Having a 5/16” & 1/8” ratcheting nut driver makes this process much easier. Don’t try this with a wrench.
After getting rid of the rat and decomposition, we sanitized the entire housing with soap & chlorine bleach.
Reassembly was uneventful and relatively easy. We ended up replacing 4 rollers, 2 belts (drum belt & blower belt), the thermistor which was damaged as a result of the blocked blower.
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
a portion of the felt seal was torn loose on the inside of the dryer and needed replacement
I spent the most time researching and confirming exactly what part I needed before ordering the shipment. The illustrations and videos available on how to replace the part(s) were VERY helpful and much appreciated.
I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - and stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.
I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.
I expected to find a broken blower belt so purchased that belt and the others I planned to replace since the on line instructions indicated that I had to pull the drum to replace the blower belt. I did not, so didn't use most of the parts at all. The instructions that came with the parts, were only slightly helpful because they were for a far different model. Some youtube videos were more help. I had to pop the top, which is easy and explained in the instructions, remove the front panel, which only requires removing two 5/16" small bolts, then lifting it up and off. Simple. With that panel off, I could see the blower belt and it was intact and seemed to work fine. I could have replaced it easily with no further disassembly at that point. However, since it was not blowing the air out of the dryer, I knew there was another problem. So I removed the front of the blower housing, which is four, 1/4" small bolts and it just pulls off. I could then see that the entire front of the blower was packed with lint that had gotten past the normal lint filter. I cleared that all out and checked that the blower itself was intact and clean and there were no other obstructions. When I rotated the blower by turning the motor, it moved easily. So I put it all back together without changing any parts and tested it. It worked perfectly again. I kept the parts for the next time I might need them.