1106808702 Kenmore Dryer - Instructions

open machine up and replaced the new belt.

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

just took off the front panel took off the belt and replaced it with the new one we watched the video pretty easy

removed front panel and drum and replaced drum support rollers

The on-line instructions were excellent; however, the man doing the demonstration used a brand new machine - not one where the old seals had melted and dried out and required serious cleaning before attaching the new seals. The new seals went on easily and I am very happy with everything about this task. I am also glad I now know what that lint chute looks like, so I'll do a better job of keeping it clean in the future.

I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

Pulled up a You-Tube vid on how to install the belt. Went perfect.

Reviewed video on how to disassemble appliance by removing drum. Removed both rollers, replaced both rollers, installed drum with new belt, test ran it w/o gas attached, so quiet a baby can sleep beside it.

i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

Drum support roller bearrings went out. Had to replace drum support rollers! It's like a new dryer now!!

First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

raised the lid, removed 2 bolts from front face, laid dryer on its back,and replaced belt, very simple. took approx. 20 min.

Opened up the dryer, to discover the broken belt at the bottom, read model, serial number. Went on line, found sites that gave parts lists and diagrams. Wrote down part no. Used Safari to find the part. PartsSelect was cheapest, had it in stock, and could ship fastest. Sears was more expensive and slower. The part arrived in 3 days as promised.Overall, it was excellent service.

I have never done this before, so I watched the video and also watched a youtube video for this model to repair belt. Used a gallon paint can to hold up the drum, while I secured the belt. whoooo hooo I did it all by myself...59 yr old Female Do it yourself enthusiast! Thanks for all the information.