Models > 1106807614 > Instructions

1106807614 Kenmore Dryer - Instructions

All Instructions for the 1106807614
811 - 819 of 819
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
sweaking while running
used your video instructions were great a great tool to repair. know wonder the maytag man is not busy ha ha .
Parts Used:
Rear Drum Support Roller Kit
  • walter from fairhaven, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken
Removed the old one installed the new one
Parts Used:
Lid Switch
  • Tomas from Orlando, FL, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
one of the Drum rollers was bad and the belt was broken
watched the repair video and had no problem doing the repairs. they were VERY helpful!
Parts Used:
Rear Drum Support Roller Kit Multi Rib Belt - 92-1/4"
  • John from Christopher, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
my dryer stopped tumbling
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me
Parts Used:
Idler Pulley Assembly Multi Rib Belt - 92-1/4"
  • joann from woonsocket, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Replaced Belt
The online vidio was very helpfull
Parts Used:
Multi Rib Belt - 92-1/4"
  • MARCUS from MACON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer tub drive belt broke
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!
Parts Used:
Multi Rib Belt - 92-1/4"
  • Ray from Salisbury, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Noisy tumbler & worn lint trap seal
Followed procedures in Parts Select web site video
Parts Used:
Rear Drum Support Roller Kit Lint Trap Housing Seal
  • Pedro from Brunswick, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
Door Catch Kit
  • Charles from North Chesterfield, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
Door Catch Kit
  • George from Melbourne, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 1106807614
811 - 819 of 819
Back to Top