1106807613 Kenmore Dryer - Instructions

video on your website made it super easy

This is a straightforward repair that you can do in an hour or less. Open the lint trap and remove the two screws. Use a screwdriver to pop up the top of the dryer. Remove two screws that attach the front panel. Now you can lift out the drum and then lift off the front panel. Clean out all the lint. Make sure the motor pulley turns smoothly. Tilt back the dryer diagonally to make the rest go easier. Loop the new belt around the drum (rubber side down) and reinstall the drum against the back wall of the dryer. Make sure the cloth liner fits perfectly around the ridge, with no folds so the drum rotates easily. Make sure the drum fits smoothly against the two rubber positioning wheels on the back wall. Position the new belt around the center of the drum. On the dryer floor, stand up the tensioner bracket. Tricky part -- thread the belt so it runs through the bracket and loops around the drive pulley on the motor, rubber side against the pulley. The belt should be tight, held by the tensioner. Reinstall the front panel so the opening aligns with the drum opening. Drop the top down, snap into place.and reattach the screws in the lint trap. Done!

Since the power and gas to the dryer were both already turned off all I had to was open the top of the dryer, remove the front panel, look underneath the drying drum and remove the belt tensioner from the belt and slide the drying drum out. While things were open I took my vacuum and vacuumed all the lint, dirt and loose articles from over time out of the dryer interior. I located the igniter, used a nut driver to remove one screw pulled the igniter from its housing and disconnected the wiring harness. For installation I reversed the process and I was done. I reinstalled the drying drum, reattached the belt tensioner, put the front panel back in place and closed the dryer top. Attached the dryer vent hose, plugged the dryer to the electrical outlet, turned on the gas and walla it purred like a kitten. It even seem to dry faster than before.

used your video instructions were great a great tool to repair. know wonder the maytag man is not busy ha ha .

Removed the old one installed the new one

watched the repair video and had no problem doing the repairs. they were VERY helpful!

so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

The online vidio was very helpfull

Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!

Followed procedures in Parts Select web site video

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

I watched the online video first, which made the removal and installation fast and easy.

In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks