11067422600 Kenmore Dryer - Instructions

I replaced belt by myself. Took dryer apart,laid dryer on its back, put belt and pulley on. Rotated drum to make sure seal was in place. Cleaned out machine while I had it apart.

Followed the instructions and really quite easy to fix. I didn't know why dryer wouldn't turn on but went with the odds that the thermal fuse was the problem-- and it was. Once I got the part it was back together and running in less than 30 minutes!

Had no heat so killed the power and disassemble the dryer form back checked the heat element and found good from an oms check then checked the thermal sensors and found bad also an oms check order the new kit and now works like it did new partselect.com got the part to me in 3 days great site yes I have them in my book marks and will use the again if needed!

Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

I Removed the rear panel. Then I used the instructions online to locate and test various parts and determined what was defective. I order the parts online and received them the next day. It took less than 30 minutes to do the repairs. The dryer works great.I will be using partselect.com in the future and would recommend them to anyone who is having problems with their appliance.

since dryers are hard for me to determine. I used my OHMs meter to see that the Thermal Fuse was good. The door switch was good . The off on switch was bad.

After viewing a series of youtube videos on Kenmore Dryer repairs, I used a volt-ohmmeter to determine that the thermal cut off was the most likely part that had gone bad. I installed the new part that I had ordered from PartSelect and our dryer was fixed.

I am a licensed electrician I found the bad part and I ordered it and when it came in I replaced it.

After watching your video, and reviewing the directions, I was able to change the rollers, the belt and tension bar with ease. The parts cost me slightly under 50.00 and now the noise is gone and my dryer works great. I am very pleased with PARTSELECT and would use them again. The parts were at my house within three days of placing the order !!!

Found the perfect maintenance kit and helpful repair video on PartSelect.com. Factory replacement parts were delivered quickly along with written installation instructions.Never needed them. Just performed the repair while watching the step by step video. Dryer works great, no noise. A very happy customer.

Removed plug. Removed lint pipe. Unscrewed lint trap under top opening. Popped the top up. Used nutdriver to remove top 2 screws of front panel. Lifted front panel and set aside. Lifted drum out. Replaced wheels and idler assembly. Parts were well engineered and fit perfectly. Vacuumed entire interior. Placed belt around basket. Replaced basket. Slipped belt thru idler pully and onto motor pulley. Tested basket one full turn to make sure the seal was in place all the way around the back. Slipped front onto two bottom brackets. Replaced screws in front with nutdriver. Dropped top back in place. Pushed down into holders. Screwed lint trap back in place. Replaced plug and tested. Replaced lint pipe. Done!

My husband and I followed the video step by step and it worked like a charm.

My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.