1106718700 Kenmore Dryer - Instructions

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

Followed Youtube video - quick & easy

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.