11066992500 Kenmore Dryer - Instructions

went online to whirlpool typed in my problem and. was directed me to Partselect which said it was thermal fuse and had picture where it was located and how to replace,easy as that.thank you PartSelect.Tim

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

i found the door switch broken was the cause of the problem and decided to replace the switch. I decided at the same time to replace the fuse link and both were very easy after viewing the video Jerry

Dryer was making intermittent squealing noises sometimes it was amazingly loud, sometimes not so bad. Still, I figured this couldn't be good so I wanted to find a fix. Read the stories here and everything pointed to the 'idler pulley', so I figured I'd give it a try. For me, access was the hardest part -- my laundry room is small and I can't easily get the dryer out or move it around. Not a problem with the part, just my own setup. Important to note that this repair is best done through the BACK of the unit, not the front. Once I got access to the back (removing AC and Water used for the 'steam dry feature') I also had to disconnect several of the electrical connectors to get the unit fully apart. Good news -- the actual replacement of the pulley took about 1 minute! It was just all of the moving and disassembly that took so long. The original idler pulley had worked its way off of the shaft and was out of place and causing the squealing. All is well now, and I saved a bunch by doing it myself. No more squealing!

my friends came over and helped me. we loved the instruction video. made it much easier.

Searched for answers on what to do when my dryer wouldn't heat and came across PartSelect videos on how to troubleshoot and repair. So I followed the detailed videos step for step and turned out to be a very simple task to identify that the thermal cut off had blown. I ordered the kit and very fast delivery had the parts in my hand in two days. Following the repair video, and a double check of the wiring diagram, had me up and running again for less than $40. I don't see a need for going anywhere else for appliance parts in my future.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

Unplugged dryer. Removed control panel end caps, removed anchor screw at each end of control panel that had been covered by end cap. Tilted control panel up to access components on back side. Using tech sheet found inside contol panel, swapped motor relay with heater relay (they're identical). Plugged dryer back in, pushed start switch; dryer continued to run (problem identified). Unplugged dryer; replaced relays to original positions. Ordered new power relay (p/n 3405281). Installed new relay when it arrived, plugged dryer in, tested it. Dryer worked normally (problem fixed). Unplugged dryer, reinstalled control panel anchor screws and end caps. Plugged dryer back in. Dryer continues to work normally.

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

your video was so helpful. It was exactly as shown. Thank You,we just had to replace a 14year old dishwasher and a 20 year old refrig. so it was great to repair the dryer.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

1.Unplugged power cord to Dryer. 2.Removed Dryer vent screen, unscrewed two screws located in dryer vent.3.Pried open top of dryer using putty knife. 4.Propped up top of dryer using 6 inch piece of wood resting on drum of dryer. 5.Removed screw holding door switch.6.Removed door switch from harness using putty Knife to pry apart connection. 7. Installed new door switch to harness and re-installed. 8.Removed wood used to prop open top, closed top, re-installed all screws, dryer vent and plugged dryer back up.

removed access panel installed new switch reinstalled access panel

Replaced Lint Screen

Replaced Thermal Fuse