Models > 11066922501 > Instructions

11066922501 Kenmore Dryer - Instructions

All Instructions for the 11066922501
1096 - 1107 of 1107
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clothes Dryer taking multiple cycles to dry
First I watched Partselect's wonderful videos on what could cause the dryer from having to use multiple cycles to dry and the parts involved. I then took the back of the dryer off and tested all three parts with a multi-meter to determine which part had no resistance. The thermal fuse did not register any thing, so I ordered the part and a few days later put it in. The dryer dries in just one cycle saving on the cost of repair and electric bill. Partselect.com is my first go to sight for any repair. They make it so simple and comprehensive that any one can do the repair. I then used duct tape to make a secure connection to the duct pipe in order for it to properly vent to the outside.

Previously I had repaired two washing machines and now a dryer, which is why my mom nick named me Josephine. So ladies you can make the repairs as well.
Parts Used:
Dryer Thermal Fuse
  • Colleen from Athens, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat.
Had a lot of trouble getting front panel off. Check You Tube for directions. Checked heating coils and thermostats and found they were OK. Cleaned lint from fan and replaced thermostats although they may not have needed it (thermal cut-off kit). Put panel back and it works. See YouTube to see how to check coil and thermostats. They may check but if something is wrong it is either them or the control board. Thermal Cut-Off Kit is much cheaper.
Parts Used:
Thermal Cut-Off Kit
  • Hubert from Luray, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't heat
should have bought and used a voltmeter first. replaced heating element and fuse and other thermostat before I got a voltmeter and realized it was the cycling thermostat that was bad. easy after that
Parts Used:
Dryer Cycling Thermostat
  • Joseph from Chadds Ford, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer continued to operate after opening the door.
I watched the PartSelect video once before the part arrived. Had the part replaced in under 15 minutes. Very quick and easy.
Parts Used:
Dryer Door Switch
  • Jerry from Pensacola, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No heat
Remove the exhaust tubing connection and the back panel (five nut screws). Locate the fuse; it is just to the right of the lint trap shoot, midway between the top and bottom of the back panel area. Replacement is visually intuitive.
Parts Used:
Dryer Thermal Fuse
  • Ronald from Gowanda, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat
I ordered the part, watched the video and made the repair in less than thirty minutes. This was much cheaper than purchasing a new dryer.
Parts Used:
Dryer Thermal Fuse
  • Harold from Miami, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The Thermal Fuse blew. Ordered the part, came the next day, total repair done. Part & next day shipping, less than $23.00
Pull off the front panel of the dryer, and replaced the thermal fuse. Very easy. Plus, vacuumed out the whole inside of the dryer, the rear and the tube running from the dryer to the outside. Will be doing this at least every 3 months to be safe. You would be surprised at how much lint builds up inside the machine. Eve though we clean the filter trap after every use of a load of clothes.
Parts Used:
Dryer Thermal Fuse
  • Daniel from Wilton, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer kept running when the door was open, no light
I followed the directions on your site. I pulled out the filter on the top of the machine. Then removed the two screws where the filter is located, I am not sure I would have found those screws had it not been for your directions. I then pulled up on the top of the machine by grabbing the sides near the front of the top, it came right up. I then raised it enough to place a broom handle to hold the top up so I could reach the switch. I removed the two screws holding the switch and then pulled the connector apart. I then replaced the switch with the two screws and plugged the connector back together. Removed the broom handle and closed the top and replaced the two screws I removed by the filter. Replaced the filter and started the machine running and opened the door and it turned off and the light came on. It took me about twenty minutes.
Parts Used:
Dryer Door Switch
  • Frank from Clermont, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Idler pulley bearings shot
Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.
Parts Used:
Idler Pulley
  • Brian from Wakefield, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not stop when door was opened
Had husband of 55yrs.replace the switch VERY SIMPLE!
Parts Used:
Dryer Door Switch
  • Helen from Fort White, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Took too long to dry
Watched the video and followed the directions. It was pretty easy, but, I ended up having to call the repairman anyway. After the heating element was put on we put the cycling thermostat on. I didn't know it, but I put some wires on upside down. I bought a heating element, a cycling thermostat, thermal fuse, and a thermal cut off kit. All that, and I still had to pay a repairman. If you're good with wires, or have some knowledge of appliances this is an easy fix.
Parts Used:
Dryer Cycling Thermostat
  • Michelle from ALBANY, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
Diagnosed problem , orders parts . Installed parts
Parts Used:
Dryer Thermal Fuse Dryer Cycling Thermostat
  • Lisa from Wakefield, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11066922501
1096 - 1107 of 1107