11066854694 Kenmore Dryer - Instructions

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

I'm almost 72 years young,but I replaced the heating Element and with your vedio it was so simple.I did it with no problem.Thank You and I'm proud of myself too.I saved a lot of money.Evelyn

Before calling a repairman, I researched the problem at partselect.com. I am so glad that I did. It saved be a lot of money. I was able to narrow down the cause of "No Heat", and ordered a new Heating Element for the dryer thru partselect.com. The part arrived very quickly, and I was able to install the new part by first watching the installation videos at partselect.com. This could not have gone smoother, and I could not be happier. And, "no", I do not work for partselect.com. :)

repair went just as describe in video.

I watched the videos associated with the parts. They were easy to understand and I could follow the steps without difficulty. I replaced both the cycling thermostat and thermal fuse. Separately, I also replaced the "push-to-start" switch. Dryer would still not start. I called the repairman. Problem turned out to be a loose wire that had shorted out in the electrical bar near the "push-to-start" switch. All parts I replaced are determined to be good and will be tried next time I experience the dryer "not starting".

Unpluged dryer first! Diconnected the vent hose.Took out 9 screws out of back panel.1 screw for the thermal fuse disconnected the two wires. Put new one in connected the wires. Then took out 1 screw that held the thermostat in place took 4 wires off. Put new one in reconnected the wires. Vacuumed out the back. Put back panel on. Connected the vent hose, plugged the dryer in. Pushed the start button & started drying clothes. Very easy!

Pulled off back panel, replaced thermostat, replaced heating element.

I followed the instructions almost exactly as the video and it was very simple. A few of the parts were a little difficult to get off but with a little tugging they popped off. After the initial installation I ran the dryer and the items didn't dry, so I ran it again and got the same result. Fortunately, not know I had already attempted to dry twice, my wife put a load in and it worked perfectly and has been since. Not sure the reason but it took 3 attempts before the heating element worked and I have a 12.5 year old drying that works good as new!

followed video on line

I followed the instructions according to your repair video and they worked perfectly. Thank you for the video, very clear and helpful giving me the self confidence to do the job myself! Part delivery was three days and the money I saved by not calling a repair man is greatly appreciated. I am already recommending part select to others at work!

To make sure the dryer didn't die catastrophically, I checked to make sure the timer, the light, and the push to start start switch and the door switch were still working. After they were diagnosed to be working properly, I unplugged the dryer and pulled it back from the wall so I would have enough room to work behind it. The first item you will need is the wiring diagram. If you do not have one, one can be obtained online by using your dryer brand and model number. The next thing you will need is a quality digital multimeter that measures resistance or continuity. The last thing you will need is a 1/4" nutdriver. The first thing you will need to do is remove the exhaust tube from the back of the dryer. The second step is to remove a small black plate located near a green ground screw. The 3rd step is to remove the large black cover on the back of the dryer. Once this is removed, you will need to locate the thermal fuse. The thermal fuse is a small component that has 2 blue wires connected to it. It is located on the housing where the steam from your clothes leads to the exhaust port. The first thing you need to do is disconnect the 2 blue wires. Once the wires are disconnected, set the multimeter to resistance. The unit of resistance is ohms and the greek letter omega is used. The red lead of your multimeter goes one metal tabe of the fuse and the black lead goes on the other one. If the multimeter measures 0. L ohms, then the fuse is bad and needs to be replaced. If the multimeter reads 00.00 ohms then the fuse is good and you have another problem. I hope these instructions were useful.

The video help to give confidence to change out the components since they were so inexpensive and the alternative was to go out and buy a new dryer.. It was easy to remove the back panel off dryer (after unplugging from the wall of course). The two components were unscrewed, cables unattached using pliers and replaced. The faulty element was definitely an open thermal fuse. For some reason there was a 5 Ohm resistance when the cables were connected.. Which confused me at first as I thought the fuse was not blown. I guess there was some conductance across the cabinet body. Anyway after replacing the fuse and thermostat the dryer was back to fully operational. I think it now actually drys better than before but that may just be wishful thinking.

I followed the instructions from the video on line. 1) Took off the back of dryer. 2) Removed electric connections to element. 3) Removed two screws to remove element. 4) Removed thermostat form element. 5) Reversed above steps to replace new element.

Pulled the back panel. Removed the connectors from the thermal fuse and checked the to see if it was good with ohm meter. Then checked the thermostat next the fuse on the left side. Then did the same thing with the thermostats at the top and bottom of the heater box on the right side if you are looking from the back of the dryer. Then check the heater element for any opens, this is where the problem was. ordered the part from this site and it took to remove the one screw at the top of the heater box and the whole heater box comes out. then removed the 2 screws on the sides and pulled the old one out and put the new one in the same way. It takes about 10 to 15 minutes to do and the dryer was back up and running. I also checked the you tube video series.

My husband followed your video