11066852690 Kenmore Dryer - Instructions

The repair was simple, and easy. And would be for any of the parts related to the issue of "no heat" or "not enough heat", however I had never used a multimeter before, and the learning curve was not simple. I ended up ordering a total of four parts, three of which weren't needed in order to perform this repair. Replacing the defective part was very easy. I wish I had been able to find better instructions on the internet or the Partselect website on how to use a mulitmeter to diagnose which part was broken. This would have saved me a couple of days waiting for the correct parts and hours of internet searching for clear instructions. It turned out that the main issue was that some of the parts needed to be checked for continuity and some for resistance. Not knowing which meant a lot of trial and error before I was able to figure out which part was broken. In fact, I really was only able to figure it out AFTER i had the new parts and was able to test the new ones next to the ones in the dryer and see which didn't read the same on the multimeter.

Upon receiving the parts from Parts Select I reviewed the contents of the package and then compared with what i had ordered. I then reviewed the video to locate the part and to ensure correct dis-assembly and installation. I had no problem with the new installation once I sorted out the wiring. Th PS video for this model describes and shows three red or orange wires coming for the harness two standard and on e thin wire which goes to the thermal cut-off. In my dryer this orange or red wire was actually bland white striped. I called PS who suggested I call Whirlpool who also could not help and insisted that this model had an orange wire where I was describing it as black, the concern was was that with this new thermal cut-off wires had to be cut and fitted with new ends to accommodate a change in design. I therefore did a little temporary wiring t before I cut any wires to ensure my assessment was correct. I was then able to cut the black and white wire fit it with a new end and plug it into the double connector that was now fitted to the jumper cable. I the connected the double connector to the thermal cut-off and tested the dryer for heat. I re-fitted the back panel and re-positioned the dryer to present everything is working satisfactorily. I would comment that someone needs to check why my dryer had a black and whit cable coming from the harness when both Whirlpool and the PS video show it as orange/red.

replaced fuse great website

We got this dryer from my F-I-L after they had to enter an elderly home. My F-I-L was a modern Tim-Tool-Man-Tyler. He had removed most of the protections and installed a 392 Thermal cut off, I guess he wanted to dry his cloths in 30 seconds or less. I was not aware of this, and used the dryer. Yes you guessed it, we sat it for a 30 minute cycle and it blew the cut-off and melted the wiring. I am a degree/certified computer tech so I fixed it myself, but I hate 220 electricity. Need less to say I checked with this site for the OEM parts and they pointed me in the correct direction. I did have to remake some of the wires since they were crisp, but it all went well and it was easy enough. The lesson, companies install OEM parts for a GOOD reason, best always to follow the makers directions.

As per online video instruction. Easy as pie...

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

Got the part in 2 days, fixed it. Thanks

I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Was shipped a new heating element and I installed it. The ordered new heating element was delivered in two days! I followed the instructions that came with the element and installed it in about 8 minutes. Piece of cake!

This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Followed the video instructions, and that was not the problem.So I ordered the next part. Then it worked.

Easy to follow videos on your site made this repair a breeze. I ended up having to replace the high temp cutoff as well but for 60 bux my dryer works like new. The repair man wanted $100 just to come look at it. Could not have done of without the easy to follow video.

ordered the part recived the parts and installed the part that easy. saved us lots of money did not have to buy a new dryer.

Removed the back panel with a 1/4" nut driver on a Ryobi impact driver. Used multimeter to check the thermal switches and the heating element. The element was broken. Went to the PartSelect web site and quickly found the part by using the model number and verified the right part by comparing the photos to the actual part. Placed an on-line order at approximately 1:00 pm and the part arrived at 2:00 pm the next day. Cleaned out the dryer vent and it works better than it has in a long time. Great web site and delivery from PartSelect and didn't have to run around town looking for the part.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.