1106607940 Kenmore Dryer - Instructions

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

just the way the video showd me

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

removed front panel and drum and replaced drum support rollers

Reviewed video on how to disassemble appliance by removing drum. Removed both rollers, replaced both rollers, installed drum with new belt, test ran it w/o gas attached, so quiet a baby can sleep beside it.

Drum support roller bearrings went out. Had to replace drum support rollers! It's like a new dryer now!!

Used repair video as guideline, I did not have their lab conditions to work in and by no means a clean machine. Also I had a two part front panel vs. single as in video, so disassembly and reassembly were OJT."on job training". Video was however very usefull in locating problem, getting correct part and accomplishing the repair. Saved $$ and machine is now working properly again. Am saving this web-site to my favorites list.

I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

When I got the door catch, I held it in a pair of pliers and pushed it right into place. The door would still pop open. After awhile, I realized that the door was bent, probably by a small child climbing up on it. I had to loosen some of the screws that held the door on in order to relieve the tension in the door so that it would stay closed. As long as it continues to work, I won't worry about replacing the door. It's in a rental house anyway.

I got my kit and when I opened it the exact parts were there!! I am a older woman and was a little worried that I could do it. I took the pliers and pulled the old latch catch out and 1-2-3 walah!! It was so unbelievably easy. If I can do it anyone can. Thank you for saving me hundreds of $s on a new dryer.

My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.