Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No hot air. Dryer turns and blows cold air.
Simply checked the thermostats for conductivity and found that they were working properly. Removed the heating element to check for conductivity and discovered a broken coil. If I had the part ready to go the whole process from taking off the first screw to replacing the element to screwing on the last screw would have taken less than 15 minutes. Very simple repair that I almost paid a service technician an additional amount for something that a novice DYI'er could do.
unplugged the dryer-- opened the back of dryer--tested the element--found there was a break in the element--ordered a new element--put everything back togethered and it worked. 10 screws held the back wall on--2 screws and 2 wires to disconnect the element---not very difficult!!
unplugged the electrical cord, took the back off the drier, unplugged wires from the bad heat unit. took couple of screws out that hed it in place, removed it , installed the new one plugged wires back , put the back on , plugged in electric cord. turned it on and that was all , works great. the part you guys sent was identical to the original . thanks. Ken
Used the trouble shooting tips provided as a guide and a multimeter to test and find the defective part. Testing indicated no continuity thru the high limit thermostat. I ordered the part and received it in 3 days. Had the repair done a full week before the repairman could even come to the house and saved well over $100 in repair costs and 2 weeks or longer of down time. Great website and service.
This was soo much easier then I thought!!! Make sure you unplug the dryer FIRST!! I removed the bolts that held the dryer back with the socket wrench. The removed the 2 screws that held the heating element in place. Disconnecting the cords was a little harder but will come off with the pliers. There is that piece of your old heating element that you need to remove to put on the new one that was hard to get off. its being held on by a metal lip and at first I couldnt figure out how to get it off, but then I just kept bending it (the metal lip) until I was able to get the piece off of it. Then just connect the wires onto the same points that your removed them from. Replace screws and back of the dryer and WaLa!!! You've just saved yourself the price of labor for an electrician.... Trust me if I can do this YOU can... My husband thought I was crazy.. I get shocked changing light bulbs but my dryer is drying a load of clothes as we speak!!!
First cut breaker off, removed wall plug, then removed back panel removed old element installed new one, had a great opportunity too clean lint from blower, and entire unit. Very good job. The video with instructions was awesome.
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Ignor installation video. it is for a different model dryer. The part is not accessed from rear. It is accessed from the front panel. Disconnect power. Remove two screws below front panel with cross head screwdriver. Swing panel up until it releases. No need to disconnect wires just put front panel down beside the dryer. Thermostat located right in front on duct easy to identify since it has four leads. Remove wires with needle nose pliers. Remove thermostat with nut driver. Contacts are labeled but hard to read. Hold thermostat so the lead number 3 (the 3 will be upside down) is on the left. Connect blue wire. White wire to top. Purple wires to bottom and right. Reverse removal procedure and you are done.
Side of lint filter (screen) cracked and broke off.
Pulled the old lint filter out and threw it in the trash. Slid the new filter in and it was all done. Doesn't take a genius to do this repair. My old dryer a sears/kenmore is over 40 years old and the lint filter fit perfect. (MF part number w10874409)
Still wouldn't work! Push switch returned to you but have not received a refund yet. The repair was very easy. Tracking # 1Z 2R5 3A2 03 0025 9453 for returned switch.
I actually bought $254 worth of parts almost to point of rebuilding , which included both roller axles, drum belt, idler pulley, both rollers, the cloth that wraps around the drum for edging, and light bulb. 15 years before this the heater element and thermostat and the belt. This dryer is 27 years old and still being used on a daily basis. The mechanical parts and no LED components can last a life time. The wife always wants new, but this dryer with alittle love and patience is a workhorse. I'm thankful for websites like this. The videos are helpful! Thank you Parts Select! Sincerely, MIke Orkin
lint screen damaged . Orordered part but did not receive it. Instead received various parts to repair clothe washer.
Item not repaired as did not receive my order. I did call the company and they said they would credit my card. Neither they nor the company the wrong order came from seemed interested in my efforts to return the wrong order. I feel this incredibly wasteful,. I would not order from a company with this attitude
