1106507830 Kenmore Dryer - Instructions

Drum support roller bearrings went out. Had to replace drum support rollers! It's like a new dryer now!!

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

Used repair video as guideline, I did not have their lab conditions to work in and by no means a clean machine. Also I had a two part front panel vs. single as in video, so disassembly and reassembly were OJT."on job training". Video was however very usefull in locating problem, getting correct part and accomplishing the repair. Saved $$ and machine is now working properly again. Am saving this web-site to my favorites list.

Viewed your video on line VERY HELPFUL, problem is the igniter will not stay on long enough to heat up. I just went back on your site and ordered a Thermal Fuse and a Cycling Thermostat for the machine but think it may be to old of a machine to keep trying to repair.

Probably could have went faster but wasn't sure on how it would go. Overall not to bad. I wish the manufacturing companies would include the breakdown of the applicances like they use to,that would have helped alot. On the front panel there are 2 clips that you have to pay a lot of attention to. Otherwise you will break them off. . Gaining access to the igniter clip was somewhat of a chore but if you go slow it goes pretty good.

I didn't have to remove the entire door...I just removed the screws with the door open, used a needle nose plier to remove the plastic insert..stuck the new one in. Then I replaced the metal portion by popping it out and inserting the new one. Easy

It Went well Part was very fragile

When I got the door catch, I held it in a pair of pliers and pushed it right into place. The door would still pop open. After awhile, I realized that the door was bent, probably by a small child climbing up on it. I had to loosen some of the screws that held the door on in order to relieve the tension in the door so that it would stay closed. As long as it continues to work, I won't worry about replacing the door. It's in a rental house anyway.

I got my kit and when I opened it the exact parts were there!! I am a older woman and was a little worried that I could do it. I took the pliers and pulled the old latch catch out and 1-2-3 walah!! It was so unbelievably easy. If I can do it anyone can. Thank you for saving me hundreds of $s on a new dryer.

My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Followed instuctions on video accept our appliance was the Duet HT model so we had a glass window to deal with. Just a few more screws to keep track of but otherwise a very easy repair.