1106304760 Kenmore Washer - Instructions

Replaced the cap over the door switch so when the door closed the switch was engaged

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you

Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred the bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

Removed the old one installed the new one

I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!

I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!

replace the water valve