11063014100 Kenmore Dryer - Instructions

The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!

I first went to your site and studied the parts diagram to see where the element was located. I then unplugged the dryer and pulled from the wall. After that I popped open the front cover and accessed the bottom of the dryer where the element was located. I then removed two screws that held the element in place and removed the wires to the element. After a little tug the old element came out. I slid the new one in place and connected the wiring and screws and replaced the cover and pluged it in. Works good as new...

I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.

Removed old filter and put in new one.

somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme

Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.

Just to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.

Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.

Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.

It was easier to remove the blower manifold cover, (3 screws) to get at the heater element. Remove the heat shield, disconnect the two wires from the element. There is another screw on the side holding the element in the housing. Remove it and slide the element torward you. I used pliers as it was a snug fit. Replace. Good time to vacuum the whole area.

Replaced

First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.

After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet metal screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.

I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.

I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.

Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected the two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks