Models > 11062622101 > Instructions

11062622101 Kenmore Dryer - Instructions

All installation instructions for 11062622101 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062622101
1,441-1,455 of 1,569
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer Belt Popped

  • Customer: Lawrence from Washington, DC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

Drive belt broke

  • Customer: Robert from Port Arthur, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

Belt broken & toe panel was loose

  • Customer: Jim Ten from Sheboygan, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

dryer belt broke

  • Customer: LAWRENCE from BANDERA, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

Clothes Dryer would not Tumble

  • Customer: John from Immokalee, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The very first thing you want to do is Unplug the Dryer. I then took the two screws out that hold the lint screen to the top of the dryer. Then I used and old butter knife to pry the front top of the machine open. The top is held in place by two plastic clamps. Once I got the top loose I raise it up. Once I had it raised, I pulled up and out on the front panel where the dryer door is. I left the door switch connected and just put the panel off to the right. I then removed the old belt which was lying under the drum. The drum does drop slightly once you take the door off. This was one of the hardest part of the project for me as I did not have any help. This would be much easier if you just have one other person to hold the drum. Anyway, I then placed the new belt around the drum and used my left shoulder / arm to hold up the drum while feeding the belt in the slot on the tensioner and then over the dryer motor pulley. Make sure you don't twist the belt. I originally had a twist and when I hand turned the drum the belt came off the pulley and the tensioner. I had to rethread the belt through the slot on the pulley and then put the belt back on the dryer motor pulley. I then gave the drum a couple complete turns to make sure everything was staying in place. The tensioner on my dryer did not look like the instructions that came with the new belt. My belt tensioner is like a half circle and the belt just rides on it. I think if I had it to do over I would have purchased a new tensioner also. I feel that the belts constant motion against the tensioner probably causes it to wear out faster. Once I made sure evrything was staying on I replaced the front panel that has the door. You just slide the bottom into the slots while holding up on the drum so it lies on the felt padding around the door. Replace all screws and presto. Works like a new Dryer. Make sure you don't forget to plug it back in... Overall it's a pretty easy fix and much less expensive then a service call or purchasing a new Dryer.

Drive belt was broken

  • Customer: Chris from Buffalo, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My husband and I followed the video step by step and it worked like a charm.

Drum belt snapped

  • Customer: James from Midlothian, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My Whirlpool washer/dryer combo is 15 years old and has given trouble-free service until this belt snapped. I went to the PartSelect website for the replacement part and found the instructional video. As a DIY neophyte I know my limits but this looked like something I could tackle and save a few bucks on. The part arrived pronto and installation went smooth as butta! I couldn't be happier and even the wife is impressed. Knowing what a service call would have cost makes the whole shebang even sweeter. Thank you PartSelect!

replacement of drive belt

  • Customer: Peter from Benton, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
after the removal of the front i removed the drum and inspect all idler wheels for ware replace if needed. if not clean and lube. idlers must be in good condition...bad idler wheels can cause the belt to brake

Old belt broke

  • Customer: Arthur from Sun City Center, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

Broken belt

  • Customer: Clayton from Girard, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Broken drum belt.

  • Customer: Bradley from Palm Bay, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Broken belt

  • Customer: James from Chicopee, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the installation video. It was exactly as shown.

Dryer drum stopped turning

  • Customer: Arthur from Felicity, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Popped the left and right side clips that hold the top, took out left and right side screws that held front face on, disconnected the wire that went to the door, tilted the door to me and lifted up from tabs on bottom. The old belt was broke, so it was easy to get off. Put the new belt on the drum making sure that the rubber ribs were touching the drum then I put the belt on the tensioner pully and motor pully. I rotated the drum by hand at least 1 full revolution to make sure that the belt was on right and it wasn't twisted, then I put everything back together. Easy 10 minute job... Art

Belt broke.

  • Customer: Laura from Saint Albans, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After looking at your video, my brother and I put the belt back on, placed the front and back on and that was it. It required two of us but it went well and the machine is working fine. Thank you.

We took towles from the washer that had still contained more water, the spin cycle must have had a problem.

  • Customer: Henry from McLean, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I felt the belt had broken since the unit was still running. I went on-line looked at some you tube movies to get some idea what to do. Was very helpfull. Found on-line how to get the part forb this nearly 20 year old dryer. Had the part shipped overnight, was able to track it. Followed your innstallation instruction, With the heavy rubber bands hooks at both ends it was easy. Never done this before, sure saved a good amount of money.
All Instructions for the 11062622101
1,441-1,455 of 1,569