Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11062512101 > Instructions

11062512101 Kenmore Dryer - Instructions

All installation instructions for 11062512101 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062512101
1,696-1,710 of 1,812
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noise due to rollers and shafts worn

  • Customer: Frank from Leechburg, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed front and back covers on dryer, screws on top and down one side to spread cabinet to remove drum,removed blower cover to get access to shaft nut on that side. The other is accessible. I found that both shafts can bethe longer of the two that were sent. The shorter shaft is too short and needed to be modified to let the roller come outward to lay in the grove in the drum. I will get a longer shaft and replace it.

Dryer made kind of a grinding noise when it started. A repair technician looked at it and said it needed new drum support rollers and shafts.

  • Customer: Janis from Lakewood, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions on the Part Select website for drum support rollers and shaft. The videos were great! (There wasn't one for the right side shaft but I could extrapolate from the other instructions.) The hardest part for me was releasing the dryer top - the video made it look so easy but it took me a long time to get the little clips to release with the putty knife. Also, tightening the new right side shaft required the help of another person as my arms are not long enough to hold the shaft with pliers while I tightened the nut in the back of the dryer (and I did have to remove the back cover for this shaft). I would recommend to anyone even a little bit handy to attempt a repair following part select's videos.

Dryer was making loud noises.

  • Customer: Ed from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had to opcn up dryer, remove drum and replace worn parts.

The dryer sounded like a thrashing machine.

  • Customer: Robert from Indiana, PA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I consulted the internet and found Part Select and use online repairman to diagnose the problem and found the roller solution with the parts, video and parts illustration. Sure enough, the left roller hole was worn and egg shaped. I ordered the parts on a Wednesday afternoon. While I waited, I got all the lint from the bottom pan, motor, and around the burner cleaned out and ready for the new parts. The parts arrived Friday morning and I installed them and put the dryer back together before noon. The dryer works and sounds like a new machine. Now I am ready to attack the squeaky fan motor in the freezer compartment of our refrig.

drum rollers worn out, making kocking noise

  • Customer: Nita from Clarkston, WA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.

  • Customer: Joe from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Squeaky Idler Pulley

  • Customer: Mitchell A. from Hampton, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

Motor noise followed by shutdown

  • Customer: Richard from Oceanside, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Before placing your order remove the motor. At the rear of the motor is a plastic nut which is how the fan is attached. Mine was stuck and needed to be removed with a cutoff wheel from the back side of the dryer. This delayed the project several more days as I had already received the motor before figuring out the fan was stuck.

Side wheel of drum support wore through bearing, sever noise at each rotation.

  • Customer: Eli from Beverly Hills, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The only added thing to know is how to remove the lower kick plate. This is not on later models. Other wise all the directions are the same as for models with a full solid front panel. Immediately below the dryer door, at the right and left end, there is a plastic clip similar to the one holding the top panel to the vertical side panels. Insert a flat screw driver or putty knife releasing the plastic clip. This will allow the kick plate to fall forward on rings at the bottom of the plate. Release springs at either side of the dryer door (reattach later using pliers or a hook). Unscrew the nut screws at either side of the dryer door. Remove the door panel and the kick plate and put to one side. Reverse to reattach. I replaced the wheel tension part and the belt at the same time. I put the dryer on its back to install the wheel, belt and tension part. I used strips of scotch tape to hold the belt in place at the top and sides of the drum, while I looped the belt on the tension wheel and the driver wheel. I used the bungee cord to hold the top in place while I put the whole drier on it back. Good luck and have a vacuum handy to suck out years of dangerous lint....

drum not turning

  • Customer: Tony from Greenville, IL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

Belt & clip where both broken

  • Customer: Amy from Seagrove, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

my dryer stopped tumbling

  • Customer: joann from woonsocket, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

Sqealing noise and extended drying time

  • Customer: Gregory from Casa Grande, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed online youtube directiond to dissassemble dryer cabinet. Everything is readily accessible and belt and idler are easily installed. Comments from others express frustration at the instability of the idler pulley bracket. The key is to keep seating pressure on bracket until the belt is installed at which time the belt supplies continuous pressure to seat the bracket. The bracket is very stable so long as moderate force is applied to hold the brackett in the seat. The belt install is counter intuitive in that the ribbed side of the belt is installed in contact with the drum instead of the flat side. The readon for this is so the belt ribs seat in the grooves of the motor pully and provide greater friction. Flat side of the belt on the drum places the flat belt on the grooved pulley with much reduced contact area.
All Instructions for the 11062512101
1,696-1,710 of 1,812