Models > 11062036100 > Instructions

11062036100 Kenmore Dryer - Instructions

All installation instructions for 11062036100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062036100
76-90 of 409
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door latch catch broke

  • Customer: Raymond from Washington DC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 3 of 3 people found this instruction helpful
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Dryer motor bearings failed. Motor wouldn't start.

  • Customer: Mark from Maple Valley WA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 6 of 12 people found this instruction helpful
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.

Wouldn't heat

  • Customer: Lorraine from Elk Grove CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 4 of 6 people found this instruction helpful
My husband said it was very easy and quick. We will recomend your site for sure.

Dryer wouldn't heat

  • Customer: Suzanne from Saint Francisville IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
Following the very helpful instructions that I found at PartSelect.com I was able to open the dryer and access the heating element which I suspected was bad. I realized later that I didn't need to open up as much as I did but the job was easy. In the future I would only open the panel below the door to access the element.

Just to make sure that it wasn't a problem with a thermostat or thermal fuse I also checked continuity from the temperature selector knob on the control panel to the heating element. When I verified continuity (zero resistance) I knew that the element was bad. Once I removed it I could see that one of the coils was broken and I should have just checked that first and not bothered opening up the control panel at the top.

Still it was less than an hour of work total. I have some experience with DIY projects but have not worked on appliances before. Thanks for the great site with good instructions and lower costs than the local parts counter.

Dryer would start and then stop after a few minutes, eventually it completely stopped.

  • Customer: Keith L. from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 6 of 12 people found this instruction helpful
After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.

I input the number into the search box and there was the exact motor I needed.

The correct part showed up in a timely manner and the pricing was very fair.

I disassembled the dryer, removed the old motor and reinstalled the new motor within about 30 minutes.

Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.

I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.

I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.

dryer will not,dry clothes,but drum run

  • Customer: atolfo from allentown PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 4 of 6 people found this instruction helpful
Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve

I recieved the kit the next day after ordering. It took about two seconds to do the repair

  • Customer: WILFRED from NORTH HIGHLANDS CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
all that was required was to push the catch into the slot notools needed.

Dryer would shut off mid way through cycle and give an E1 error code

  • Customer: Dwayne from Bainbridge PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 4 of 7 people found this instruction helpful
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Not heating

  • Customer: Manuel from Key Biscayne FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!

When using the dryer the cycle would stop and display E1 as the reason

  • Customer: Joyce from Holbrook NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

gas flame would shut off after + or - two minutes

  • Customer: RICHARD E from UNALASKA AK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
the igniter worked so replaced the two coils on the burner, did not help, read the diagram that came with the machine and replace the high limit cut out. that did it, however the mounting bracket needed to be modified by grinding a tab off, so that the cut off switch would fit in to the bracket.

Dryer electrically dead

  • Customer: Dale from Anderson IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.

Drum would not spin to drain water

  • Customer: Gay from Apple Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Dryer would not run

  • Customer: james from york PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Lens melted because paper got behind the lens and was heated by the lamp.

  • Customer: Chris from Valley Stream NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
1 screw to replace.
All Instructions for the 11062036100
76-90 of 409