11061082000 Kenmore Dryer - Instructions

Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw holding heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

take off front bottom panel. use ohm tester on the heater coil element, (It had broken in back) remove screw holding it in place and the two red wires leading to the element. Pull out and replace. reinstall in reverse. Done

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Ezee pezee lemon squeezee.

Just like the video, just followed the video
Thanks,

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

Watched on-line video on how to disassemble and test heater element, thermostat, and hi-temp shut down. Heater element was open. Ordered new heater element. Re-installed heater element iaw video provided with parts. Video provide was one of the best I've seen. Explanation on releasing access panel was especially helpful.