11060902990 Kenmore Dryer - Instructions

My dryer element was not heating and there did not appear to be any damage to the element itself. There were several thermal fuses attached to the heating element enclosure. Test them with a voltmeter and see if there is conductivity. If there isn't, then the fuse is faulty/broken. Replaced my broken fuse with 3390915 and the element heats once again. The original part was not the 3390915, but Kenmore recommends replacing the stock thermal fuses with 3390915. Thank you!

Replaced actuator switch lever. Exact replacement. Worked like a charm.

Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.

We thought it wiras the heating element and we ordered that part from.you but it did not fix the dryer. So we ordered the thermal kit and little less then 15 min. we had it fixed.

Found this part on your site very EZ bought it you shipped to my door got it when you said it would be here open it installed it propblem over glad i found you guys will use again Very good website Keep up the good work THANK YOU

Order one new latch, receive 2 spares. Pushed new latch in, re oriented the catch. was done in less than 5 min

Simple to remove the back cover, two screws holding the timer, unplug wires from old timer, install on the new one. New timer was exact match to the old one.

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.

Removed front lower panel as shown in how to do video, removed two screws from heating element bracket and pulled the whole tube that holds heating element and thermo cut off and thermostat. Used OHM meter to check out heating element, thermal cut out and thermostat. Thermal cut out was the only thing bad but replaced both thermostats as recommended. The most time was taken cleaning out cabinet as it had eleven years of lint and very lucky it never caught on fire over the years. Put all back together and dryer now dries clothes in half the time as before.

Followed the directions from your vidio,it was a snap.You Guys are the greatest!!!

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.

removed old one installed new one.

I took off the back panel, removed the 2 screws each for the thermostat and cutoff sensor, removed the 2 wires that went to each, screwed in the new parts, reattached the wires, and bingo, the dryer produced heat again. This was my third and final shot at trying to fix this problem as I had already replaced the thermal fuse (was not the issue), and replaced the actual heating coil (apparently wasn't the problem either). However, the dryer is now working better than ever with the new heating coil, drying in about half the time it took before, so I'm glad that was done.

Checked the element and switches. Found thermal cut off switch open. Order new switch. Installed switch and vacuumed cabinet. Start and test.