11060854990 Kenmore Dryer - Instructions

The new lint screen fit perfectly. All I had to do was slip it in the lint filter slot.

removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

watched you tube video. removed back panel, tested thermostat with multimeter-was ok. 2 more nuts to remove heating element - tested bad with visual break in some elements. easy replacement.

I ordered the heating element It was one of the easiest dryer repairs I ever did. Thank you

I watched several Youtube videos for this repair. The best showed a man taking you through every part of replacing the rear felt seal. I used binder clips from my home office and he used clothes pins to keep the seal in place while gluing it and letting it set. To completely finish this repair, it takes over 24 hours to get your dryer ready for drying again. Steps to repair: you need to get to the dryer drum, watch a video on how to do this to include taking off belt, idler pulley. Remove Drum from the dryer. take off all the old felt seal. take out new felt seal and place around the drum, it will be pretty tight. secure the seal by using clothes pins or binder clips all the way around the drum. this will help you keep the seal on the drum and guide you as you use the glue to bind the seal to the drum. Using the adhesive provided with the felt seal, going around the drum, glue down the seal and re-clip it so the glue gets a good grip. let dry of at least 1 hour. Cannot use the dryer for another 24 hours to make sure the glue dries completely and is ready for the heat. I had already replaced the 2 rollers, 2 shafts, belt, idler pulley and start switch and dryer still squeaked. Then I replaced the rear felt seal. NOW I am replacing the bulkhead because it is worn flat in some places and is warped. I am waiting on the part.

I researched the issue, found a video and ordered the belt, which came in 2 days. It was inexpensive, and I had my dryer back and running in less than 3 days. I did get my son to help me as it might not be that easy with just 1 person (to hold the drum in place while putting the front back on). Great service and great information on how to do the repair.

When we ordered the part we watched the video, to see what needed to be done and both my husband and I got the dryer all ready for install before part came so when the Ups delivery came it took all of 10 min to get it back up and running! Thank you so much for having the details and a video made thing go so well! Sincerely Dawn

Installed a new heating element. Very simple installation and it took me 5 minutes. The part was available locally but for double the price. I ordered the part on a Monday and received it the next day.I would definitely use your company again in the future.

Removed back and found fuse bad, repalced fule.

Disassambled the dryer and vaccumed and clean dryer inside and out. Ordered the parts and reasembled. The old style front end loading dryers are easy to work on. Remove the top screws under the lint screen lid and pop the two clips on the front corners and the lind folds back. Take out one scre on each side of the front pannel to gain access to the drum. Just slide the belt off the drom and clean. Take off the back cover and access the heater coil and rplace pretty easy.

I loved the demo video on how to do the repair-it was very helpful. My dryer was different than the one on the video, and I had to make adjustments ( I had self tightening screws on the top and bottom of the front panel and then I stripped the screws)I did this by myself and I had to prop up the drum AND the front panel with items in laundry room.) That's why it took me longer than demo (also had to run to hardware store to get screws). Felt great to accomplish this by myself. Thanks!

burned out removed dryer back panel (10 screws) and power cord then i removed heating element (2 screwa) unplugged 3 wires. then replaced everything on new part quite easy dryer now heats up

Turned the dryer circuit breaker off. Removed the console from the dryer and then removed the screws holding the back plate. I then pulled the spade lugs off the terminals of the pushbutton. To remove the pushbutton from the console I had to turn the pushbutton so the square on the pushbutton aligned with the square hole on the mounting base of the console. This allowed me to remove the old pushbutton. I was now ready to install the new pushbutton. I aligned the square on the pushbuuton with the square on the mounting base. Once inserted in the square hole , I rotated the pushbutton securing it to the base. I reinstalled the spade lugs on the terminals of the pushbutton. I then secured the back plate to the console and put the console back onto the dryer. I turned the breaker back on and tested a dryer cycle. It worked!

Followed the instructions provided by Parts Select and it was very easy and quick to fix !! Thanks Part Select for everything!!

I work with a phillips screw driver and a flat screw driver I pry the both sides in front to lift the cover I propped it to axcess the door switch wire then I open the door to remove the two screws I removed the tabs from wiring and I did the reverse to assemble then plug the cord back on the wall it took me less than five minutes. Thanks for your advise on the demonstration on the vedeo clip thank you for the switch too merry christmas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .