11060612990 Kenmore Dryer - Instructions

The dryer opens up pretty easily; there are two screws holding the lint filter housing to the top panel that must be removed before the top will come up. The top panel pops open by prying it up with a screw driver. Once it's off there are two screws inside near the top that hold the upper front panel to the sides. There are also two screws that need to be loosened, but not removed, at the very bottom of the upper front panel, accessed by removing the lower front panel which is also popped out by prying (the upper part of the lower panel is pulled straight out, and is held to the bottom of the unit by hinge-like clips). Once the upper front panel is wriggled back the drum will slump off but stay pretty much in place while you set the panel aside (it has an electrical lead that goes to the door-closed sensor, but if you pop its clips loose in a couple spots you'll have enough slack to set it to the side). The drum pulls off easily. You might want to take a photo of the belt/pulley arrangement underneath it before removing everything, as it is not intuitively obvious how the belt runs thru the pulleys. Once the drum is gone vacuum up all that accumulated lint, then pop off the metal clips that hold the motor on. I was surprised at how little holds that motor on; apparently it's enough. Here is where I ran into my one snag: I couldn't unscrew the blower wheel from the motor shaft, and you have to get that fan off to get the motor out. You're supposed to clamp a wrench on the plastic fan just inside the dryer housing, and unscrew it by turning the shaft from the other side. No go. I eventually drilled a sequence of holes into the plastic around the metal shaft (easy) and could pull the motor out, but of course now I needed a $20 fan replacement. The motor and fan showed up in 2-3 days. Unfortunately, the motor came with a pulley that needed a narrower drive belt than my original. I guess I could have cut the original down, but i just went ahead and ordered a new one ($12). Everything went back together surprisingly easily. Getting the new fan on was much easier than getting that old one off.

Unplugged Dryer. Removed back panel of the dryer. Disconnected and removed the Thermal Cut Off switch and replaced. Disconnected and removed the High Limit Thermostat and replaced. Reinstalled rear panel of the dryer. Plugged in dryer. Operated dryer and checked for heat. Operation was proper and dryer works great.

Took the back off, swapped out the three sensors. Just like the videos showed. Easy as pie!!! Took more time to vacuum the dryer out. , Excellent delivery time and customer service!

opened back panel and replaced the ordered parts. Runs like new.

take two phillips srews out of lint catch frame. next take a screw driver pry up front top part on dryer.lean back top out of way.take two screws out of top of dryer door. disconnect electrical connection dryer door frame.and pull frame upward and off. you will see roller bracket with end made to put in slott. put it in first slott under belt motor.take belt and pull it through under roller and hook it with screwdriver to motor pulley.by putting the tip of screwdriver on motor pulley with belt on screwdriver and lift up until belt slides on to pulley. make sure you put belt around barrel. before putting belt through roller bracket and on to motor pulley.and use something to put under barrel so it will not get in the way and fall off.

I checked the site, diagnosis - need thermal fuse and it suggested replacing thermostat as well. Viewed the video. Removed dryer hose. Used a 1/4 hex socket to remove screws from back of dryer, removed the screw from thermal fuse pulled out the fuse; inserted the new ones wires to prongs and screwed it back in. I did the same thing with the cycling thermostat. Terrific while I was in there; vacuumed all the dust out. Screwed the back on, put the vent hose on. $36...Very Happy!!! Also, viewed their video to access drum. Fixed the floppy fin inside dryer and vacuumed arount drum as well! BTW....I am a 65 year old woman!!! A very happy one! The initial job was about 20 min...doing vacuuming and drum repair was a lot longer as I had to hunt down washers to put on one of the fins so it wouldn't keep moving. Cleaning the fin of debri and lining it up etc Total time: maybe an hour and a half. TIP: People should wash their lint filters at LEAST once a year! Helps prevent overheating and fires! Thank you Part Select! Linda :)

Watched the repair of a similar repair on a video and took off the heating tube which was found to be defective because it burned out the heating coils. Replaced the heating tube and it's working fine.

i popped the top off. removed the 2 hex screws in the front upper inner corners. lifted the front panel up about an inch n removed it. pulled the drum out. removed the old broken belt. put the tention roller back into the slots at the bottom panel n base of the motor. mounted the new belt around the motor n thru the tentioner as i placed the drum in position n mounted the belt around the drum. holding the drum in place i replaced the front panel. replaced the hex screws n closed the lid. wah-lah. dryer fixed... thank you parts select

i got in partsselect website and related the dryer problem and they recomended replacing thermal fuse or cycling thermostat, i replaced both,started dryer after a few seconds dryer was heating up.thanks to partselect expertsi i saved time and money. thank you partselect!!

Looked at the partselect video on you tube, piece of cake.

My dryer was made so the fan was not removable and I had to reach through a narrow opening in behind the fan housing to put the belt on the motor pulley. The problem I encountered was that I could only use one hand to push against the idler pulley spring while at the same time try to catch the belt and slip it under the idler pulley. It repeatedly slipped off and every time it did the spring and idler pulley would come loose, and I would have to realign the the idler pulley shaft and attach the spring. After the fifth time I left the spring off, pushed the idler pulley shaft all the way in and put scratch a mark on the shaft on the inside of the first hole it enters. Next I drilled 1/16" hole in the shaft where I marked it, installed the spring and idler pulley then slipped a small cotter pin in the hole I drilled. Now if it slips off I only need to reach back and push the idler pulley up and catch the belt.

I tried all standard tricks: checking circuitry, switches, etc. Then I read other submissions on your site, which suggested this thermal fuse was the culprit on almost 50% of cases. I got yours in 2 days, installed in no time, easy as pie. One caution: it will take an entire day if you forget to close the dryer door completely.

Viewed the videos on PartsSelect site and determined the most likely (common) problem. Ordered the Thermal fuse and recommended Thermostat. Received in only two days with standard ground delivery. Took the back off the dryer, and it took all of 10 minutes to install the new components and vacuum out the lint that has accumulated and caused the overheating. Now this 10 plus year old dryer works perfectly for a total of only 36 dollars and some change. Can't beat that!!! Will definitely use PartSelect for other repairs.

Disassembled front & top of dryer, removed drum & replaced belt, idler pulley & one support wheel (which was the problem). Reassembled drum, top, & front of dryer. Tested good, much quieter.

I followed instructions from video -- although the model used in the video was different, the approach was similar. Really the only difficulty was laying on my back (72 years old) and, with one hand and through feel alone (work area was not visible), getting the belt on the drive sprocket and the spring loaded wheel.