11060232002 Kenmore Dryer - Instructions

pretty simple fix not much to it. If you are familiar with electrical work a dryer is just about as basic as it gets. Thermal fuse was bad, swapped it out and up and running again. It took me longer to get the dryer pulled out and cleaned up, than it did to replace the fuse. Wow was it diry back there!

Very easy to installation,first belt has to go on drum and then through pulley,pulley go on it`s place ,need some pressure on pulley to instal it.Very easy.Thank`s for fast belt delivery. Richard

Watched the video but realized my dryer was a little different removed bottom front panel to expose area to remove thermal fuse. Checked for continuity, found that there wasn't any. Ordered part and replaced it, fired right up!!

Ordered new rollers from PartSelect. I followed the video to replace the rollers. Everything went well. The video did not show how to put the belt back on. I then went to replace broken belt and there was the way to go through the pulley. Works great with no noise. Just like new. Thank you

My husband who is in a wheelchair and his freind who had never worked on a dryer,watched the video online and boom! just like that it was fixed!Some nut told me it would cost too much to fix,To just get a new one!Boy am I grateful for you!Thank You.virginia.

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.

layed the dryer door side down, took 6 nuts off back metal panel, then took the bolt off at bottom and reached in and pulled drum support rod loose, removed old roller, installed new roller, reached in set drum support rod back into hole where the threads were showing on the outside where the nut was then put back on and tightened back up, put a pair of vicegrips underneath on rod to hold in place while tightening up nut,placed cover panel back on with screws and now it works like a new one, runs very quiet. Cost was 25 dollars for part nothing to do it ourselves. We priced new dryers that size they're well over 400 dollars. Easy REpair!!

I had purchased a motor for the dryer first. The blower wheel broke while I was trying to take the motor off from the blower wheel. Installing the new wheel was fairly easy once I took the blower cover of at the back of the dryer and literally brake the wheel of the motor shaft.

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.

Removed back of dryer and the fuse was right there in plain sight. Had to remove a screw and pull contact wires from fuse. Attached wires to new fuse, replaced screw that held fuse in place. Replaced dryer back. This web site is great! Diagnosed my problem, and then received the replacement part the next day! I will use the site again, if necessary, and recommend it to others.

I replaced the thermal fuse and it started right up.

Well it took me longer to get the dryer apart and than it did to get it back together... Well I opened it up it was obvious I had burned up the motor you couldn't even see it for all the lint that was built up around it... And the hardest part was removing the fan from the motor shaft, I didn't realize it was plastic and sort of mangled it getting it off so I went ahead and replaced it as well. The hardest part of the whole repair was removing and replacing the clips that hold the motor in place and there didn't seem to be any trick to it, I used a pair of channel locks and a little muscle to get them off and back on everything else was a breeze! I recommend checking the exhaust pipe at least once a year to make sure air is flowing freely to prevent the lint build up inside and even more often if you have a long run. This should prevent having this problem again...

changed the top thermastat

Read the Use & Care Guide! I spent several hours trying to repair a dryer that was not broken because I was unaware of the "lint signal". While replacing a burnt out heater element I apparently disturbed the flapper on the lint signal box and it stuck in the open position. My wife who does the laundry has always kept the lint filter clean so we had never heard the lint signal and I assumed that the high pitched sound I was hearing must have been from a faulty gasket, belt, roller, pully, or motor. Boy is my face red!