11060022010 Kenmore Dryer - Instructions

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

follow the vidio. removed lint screen. removed screws securning the lint trap guide. used to disconect the two clips honding the top cover and lifted it up and secured it as not to drop down. removed two screws at top of front paned and removed it. took out drumb. took off the two rollers and remounted the drumb and belt. replaced front panel and two screws. lowered top panell and two screws. replaced lint trap. turned on to see is noise stoped and it had. done

I took the back panel off, after moving the unit away from the wall, and disconnecting the vent hose. I replaced the cycling thermostat, and high limit switch, and for good measure, I replaced the heating element as well. The diagnostic tips on the PartSelect website were very helpful. I cleaned all the accumulated lint out of the unit while it was apart, then reassembled it. The dryer is working just fine now!

I had knee replacement 2 weeks before our dryer stopped working! My wife took the rear panel off & replaced the parts under my reading the instructions ! Very easy to replace!

Used video of PartSelect guy on YouTube to diagnose bad thermal fuse with multimeter. Removed back panel of dryer with nutdriver, removed thermal fuse, found no conductance across terminals. Ordered new part. (It arrived very quickly!) Put in new thermal fuse, replaced back panel. Shortened flexible vent tube so there would be fewer bends. Dryer works now.

I unhooked the gas line, removed the vent hose and then removed the back of the dryer.I replaced the thermal fuse and the cycling thermostat in about 5 minutes. Most of my time was spent vacuuming dust in and around the dryer. The job was easy and my 14 year old dryer works like new.

Unplugged the cable and removed the air-vent hose. Removed the rear panel. Marked and removed the wires from both thermostats. Prior to replacing the new parts I used the vacuum and cleaned all of the excess lint and dust from the dryer. I then installed the new thermostat and fuse. Simple..

David

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

The dryer belt was delivered promply, afterwards I lifted the top of the dryer and unscrewed the front panel, so it would lower. Then I watch a 5 minute video and it clearly demonstrated how to install the belt. This was my first time, so it took about 30 minutes.

after replacing my heating element, my dryer still wasn't heating. So i replaced the thermal cut-off unit. from ease of finding the part, to ordering and the instructional videos...this was a no-brainer.thanx guys!!

It could not have been easier, thanks to the video displayed when I ordered the part. It was as easy as removing the back of the dryer, taking out the old fuse and putting in a new old. I have NO repair experience, so little I had to borrow the nutdriver from the maintance man at work. I was more then a little leary to try this repair on my own, but decided it was worth all the money I would save not having to call a repair man for my dryer. Sure glad I did I will continue to attempt more repairs on my own.

i replaced the two sensors in the heating element which were very clear in your diagram and it worked perfectly

Checked voltage coming into unit, good. Checked schematic and traced the voltage through the safeties and interlocks. Found the problem at the thermal link. Isolated unit from all voltage sources. Removed part and ohmed the resistance. Found it open. Ordered new link and it arrived before schedule. Replaced and connected wiring, returned power and tested. Worked great! Very easy to find and repair!

PartSelect sent the exact right part, and very quickly! YouTube showed me how to install it. The only hard part was the bulkiness of the drum, which is why I marked "a bit difficult" for the repair.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).