11047512602 Kenmore Washer - Instructions

I simply followed the video instructions which was presented very clear and the video shots was on point

I thought there were just two screws to do the replacement. However, it is necessary to remove the entire plastic outside cover to accomplish this task. There are several screws on the inside of the door, some attach the door to the hinge. Check your manual to determine witch these are. What I ended up doing was completely removing all screws and the door. reassembling was a bit difficult but I got the job done.

one note, remember which screws came from which holes as they are close in size but a little different.

Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.

raised front of machine about 6 inchs bigest pain is getting water out after that its easy.open drain just a bit other wise it will pour out all over about 4 pots worth if its full

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

Just went by instructions provided by parts web site

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!