Models > 11045087400

11045087400 Kenmore Washer - Overview

Get Parts and Repair Help for 11045087400

If you know the washer repair part you need, you can browse the list of all parts on the 11045087400, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 11045087400 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$82.92

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

$23.12

Drum Baffle

This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle. Sold individually.

$137.11

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$73.55

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$53.75

Water Inlet Valve

Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$31.68

Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Note: They are sold individually. Order quantity needed.

$13.64

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$4.65

Touch-Up Paint - White

$3.76

Door Hook/Strike

Attaches to door lock mechanism.

$14.54

Bellow Clamp

This is used to help hold the bellow in place.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 215 of 231 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 109 of 113 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 88 of 101 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more