Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Would Stop In The Spin And Drain Cycle
Unscrewed two screws that hold the conrol counsel and tilted the control counsel back. Disconected brass clips that held the back of the unit to the cabinet tilted he cabinet back toward the front and slid it off. Disconected the wire harness for the switch and unscrewed the two screws under the lid and took the switch out replaced the switch put the screwes back that held the switch in place tilted the cabinet back nd slide it back on refastened he brass clips tild the control counsel bak replaced the screws the hole repair took about 30 minutes fairly easy to do with just a flat head and philips screw driver
I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self. But I read other peoples experience on fixing the same problem that I had so I gave it a try. I will not hesitate to do other jobs myself. Doreen Finlaw
Tub not spinning or agitating, but could hear motor working.
Disconnected power, all hoses. Tilted washer backward to see underneath. (Placed sturdy 6" high object under back of washer to keep it from going flat on ground and possibly damaging hose connects). Looked for area where motor and transmission connect. Saw broken part (coupling). After trial and error, figured out how to remove pump and then motor, by removing strap type holding clips, and then broken part was accessible. Ordered part online and was easy to install and reassemble washer now that I knew how it came apart. If I had known the part name or number beforehand, I could have watched the replacement instruction video on this site, but I figured it out anyway, and I did it without removing the whole control switch panel and side panels/body of washer, like they do in the video. But..I guess they had to do that to give you a good view of all the parts and things they were removing underside. I recommend watching video for this part install,so you see what needs to be removed and how underneath, but then just tilting washer back to access underside, without all that control panel and sides removal.
Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!
researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack When it came out it was full of rust and grime - it would have never come out without what we did Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't spin with load, then not at all with rapid clicking sound
Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems
the washing machine would pump the water out, but the agitator would not spin, and it was making noise.
The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts. Thank You, Mario for Eastchester, NY.
Honestly, it took more time to figure out how to get at the dang thing than it did to replace the assembly. One screwdriver for the whole project. Very easy to figure out (once I got into the machine casing, anyway).
Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.