11026955691 Kenmore Washer - Instructions

I watched the how-to video twice and the repair was just like it. My only tip would be to have a pan or floor drain nearby to empty the drain hose prior to tipping the machine on its back.

We followed the instruction from your site on the Internet ( Video-Demo ). Everything was very simple and very easy.Thank you for that , we saved a lot of money .

watching the video was a great help, not a perfect match as mine but enough information to get the job done! parts were cheap & they shipped fast. keep coming with the great videos!

After i pulled the motor off the washer, i found the coupling that was busted,removed it and put on the new one i got from you and just put everything back together again and the machine is operating as good as new again.

watched the repair video on u-tube and followed it. Had trouble separating the top agitator from the bottom agitator after removing it from the washer. I tapped the 4 white tabs on the top with a hammer and screwdriver. Top and bottom separated after that.

I noticed the top wasn't spinning. I took the cap off the agitator and looked inside it. Sure enough the directional clogs were broken. I had no idea what to do. I went online using my phone and discovered partselect.com With their wonderful help I was able to find out what part I needed and order it right from my phone. It only cost me $10 bucks to get it delivered to my house and it shipped in 3 days. I am 21 years old and this was my first washer. Thanks to part select I can keep my washer. Partselect saved me well over $150 dollars plus labor. I will definitely use partselect again!!!

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

Followed an online video. Very informative.

Video's on parts select are a big help. Just followed the instructions. Only slight problem was the coupling's do not slide easily onto the shafts. I had to use a little lubricant and put a wood block across the opening and tap with a hammer. Maybe a little more than a tap. Also when I was ready to test the repair I found the washer would not stop filling. After much checking I found out on another repair site that the shutoff requires a certain water pressure to work properly. I hadn't opened the faucet fully. Once I did everything worked properly.

Easy, popped cap off top of agitator with edge of knife. Removed bolt from center of agitator,pulled agitator up from shaft. Removed old,worn cogs,replaced with news cogs and reassembled. Tightend with bolt . Replaced cap and bang ,works like new.

Removed the actuator cap which gives you access to the screw that holds the clutch dog assembly in place. Once the screw is removed the assembly lifts right out. The clutch dogs have a small retaining band that holde them in place. Once removed the dogs slip right out. Replace the old dogs and reverse the order of the removal process. Very easy.

pull off softener dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

Pretty simple task, and pretty much followed hints in the video provided by the web site. Unit worked fine after replacing the parts. Most awkward part of the job was getting cabinet back into position to secure to the base. A bigger working space or a second pair of hands would have helped in securing cabinet. Only took over two hours (working slow) because cabinet kept sliding out of position while trying to secure.

I went on your website and saw the video on how to take the lid switch of and I just follow instruction it was real easy I was finish in minutes thank you for your help.

Based on the excellent professional video instructions attached on the order delivery verification from PartSelect, I followed the step by step Lid Switch Assembly installation process as shown on the video which was specifically geared for Kenmore 80 series. My installation turned out flawless and the machine was up and running in about 45 minutes.