11026942503 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water running from under washer
I found the impeller, in the water pump, had worn thru the front pump housing. Allowing water to leak on to floor. Replaced pump from under washer. Removed two hose's and two retaining brackets. Aligned pump and refastened hose's and retaining clamps. Works great. Thanks to Parts Select for the right part and the right price. Also Fast shipping. Dan H. Poplar Grove Il.
Parts Used:
-
Daniel from Poplar Grove, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
agitator stop working
-
Floyd from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Water not draining.
Started to replace the water pump but looked online at Youtube and everyone said to look at the lid switch first. I bypassed the switch and sure enough that was it! No need for the pump.
Parts Used:
-
James from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer would fill with water and then stop.
My brother-in-law did the repair. He unscrewed the back of the top part of the machine. He located the lid switch, which is on the right from the back of the machine (left if you look at it from the front). He then unscrewed the ground wire and unhooked the old lid switch. He put the new one in place, hooked it back up, screwed the ground wire. Reconnected everything and now it works.
Parts Used:
-
Ashley from Breaux Bridge, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
would not always spin & was leaking water
Tilted the washer on the side with my wife holding it. Pulled the pump out then replaced it with the new one.
Parts Used:
-
John from Bakersfield, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Washer would not begin to agitate clothes after fill.
Lifted up the control panel, removed the broken lid switch and replaced it. Replaced missing Lid hinge mounting screws. It was great. Fixed the problem. Felt empowered to fix it ourselves for such a reasonable cost. Thanks
Parts Used:
-
Sharon from Florence, MT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not spin,but would fill and drain and could hear motor and trans worked
Follow instructions in part repair video from part select,but put washer on back first to see if can access area without removing the whole outer cover we did not even need to do that step only took 20 minutes to replace coupling. The video was great
Parts Used:
-
Diana from Sherborn, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin and we could see coupling was broken
We watched the how to video...repair took less than 15 minutes. You can't go wrong if you just watch the easy to follow video! Washer works as good as new.
Parts Used:
-
Sharon from Marina, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!