11026632501 Kenmore Washer - Instructions

Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

The hardest part was understanding how to take the cabinet apart. The "exploded" parts diagrams at PartSelect helped immensely.

I just followed the steps on the video, I was surprised how fast I got the parts within 24 Hrs . Thanks

Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.

The top of the agitator pops out and leaves the fastener(a 17mm bolt) open at the bottom of a 6 inch or so opening in the top piece. That bolt comes out with a socket extension and the top comes off. Replacing the dogs is just a case of sliding a retainer ring down, removing the broken dog pieces and replacing with new dogs. Reverse the disassembly process to reassemble the unit. Now, it works great.

followed the video on the web site and repair was amazingly easy. I have two of these machines, and this same part went bad about 1 1/2 year ago, so this time i was ready for everything. Took everything apart, got rid of old broken part, replaced with new, and Bam, washer back up and running, less than 30 minutes, I am limited on space in my basement, so i didn't turn machine on its back, i did it in the upright position, just utilized some wood blocks to hold the motor during part change, and a hand spring clamp to hold pump and hoses out of my way after removing the clips that hold it on. It's not rocket science, if i can do it so can you. Good luck

First, unplug the unit. Remove the two screws on each side of the control panel on the back. They are located at the top corners of the unit. The base is held on by clips you press in on from the bottom. You will have to reach in over the tub and press in on clips, one each on the far side. At the left, you will be able to feel the lid switch, the clip is just to the left of the switch. It is about ½ inch wide, press firmly with your thumb. You may want to wear glove for this unless you like battle scars. Once done the control panel should hinge up. The switch is on the left side. To remove the switch, I first detached the wire harness to the control panel and unscrewed the grounding wire. Open the lid and the switch pulls right out. The new switch drops right in. Attach the wire harness and grounding wire. Place the control panel back side first at an angle making sure the back metal panel is lined up, once in place it should snap back in place when pressed down firmly. You might have to reach in over the tub again and pull the clip down (keep Band-Aids on hand). Plug the unit back in and you are good to go. Raise and close the lid, you should here the switch click on and off.

Removed softener dispenser from agitator. Removed 1/2" bolt from inside agitator and removed top half of agitator. Removed cog assembly. Used screw driver to pry slip ring up 1/4 " to access directional cogs. Replaced cogs, pushed slip ring back into place. Reassembled agitator in reverse order of disassembly.

First I tipped the washer forward and placed a plastic milk crate under the rear of the washer to support it . Then tipping the washer back. I placed two car jack stands near the front to support and level the machine. Now I had enough room to look under it to see where it was leaking. Right away I could see a drip coming from the pump in the front of the washer. I removed the two water hoses. Then with a screwdriver popped a clip on the top of the pump and one on the bottom. The pump slid easily off . Slide the new pump on and reverse the process

Followed written instructions after viewing repair video. Would have been helpful to know how far onto shaft each drive piece needed to be placed. I should have noted old piece placement, though if this was noted in instructions it would have been reassuring to know what is the proper placement. I also placed machine on its back to align the motor and transmission after new parts were installed on each.

We started to get water hammer in the pipes when ever the washer was set to cold? Looked it up here and figured the inlet was about to go out, ordered the part, 2 days later, brand new washer, no more problems. Local repair would have cost us at least $100.00, part was $25.00 shipped, videos are awesome tools, PartsSelect Rules!!!

I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

The repair was easy and the video tutorial was great. That was the easy part. I also had to replace the drain pan and getting it in and out of the pan is no easy task. Plus when you have not moved the washer in 10 years there is some cleaning to do. I would not hesitate to do it myself again. It cost me $20 and some sweat equity.

Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.