11026332500 Kenmore Washer - Instructions

After i pulled the motor off the washer, i found the coupling that was busted,removed it and put on the new one i got from you and just put everything back together again and the machine is operating as good as new again.

My washer leaked water in after wash cycle and cloths were wet after spin cycle. The cause of problem was defined in Parts Select trouble shooting guide. Replacement was just as the video described, except this model had two screws on front of control panel and the panel tipped back on hinges. Look at both sides of washers, so when you reinstall the body you know how it should look against the back panel. I didn't slide the whole washer body off, just tilted against a wall. Also, it's not necessary to get behind the washer, so the repair can be done in a tight laundry rooms like mine.

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

Followed an online video. Very informative.

Video's on parts select are a big help. Just followed the instructions. Only slight problem was the coupling's do not slide easily onto the shafts. I had to use a little lubricant and put a wood block across the opening and tap with a hammer. Maybe a little more than a tap. Also when I was ready to test the repair I found the washer would not stop filling. After much checking I found out on another repair site that the shutoff requires a certain water pressure to work properly. I hadn't opened the faucet fully. Once I did everything worked properly.

very easy I followed the Parts Select video that's posted at the site,and covered the replacement very good.Thank You very much.

Turned washer on back, inspected pump area for leak and found crack in pump. Replaced cracked pump with new pump from PartSelect, which arrived promptly. Washer was only down for 3 days and turnup only cost me the price of the part.

Saw your video on how to install a waterpump. It made my life very easy.

Wacthed repair video online found problem ordered part 3days later part came installed worked like a charm smootest repair ever thanks john I told a neighbor about your service

Tilt the washer back enough to access the bottom of the washer. Remove two hose clamps with pliers,then remove 2 hoses attached to pump. Remove two metal spring straps and remove pump. reverse to install.

Let me start by saying that I only had to wait one day for the new water pump. Awesome! Once I figured out how to accessed the waterpump, the real challenge began. The washer had been leaking for some time and removing the old pump turned out to be more difficult than expected. The bottom clip used to secure the pump was completely rusted. It took some effort to remove the old pump but it finally came off. Once it was removed, I discovered why it was so difficult. The drive shaft from the motor was so rusted that a groove had been worn into it. I ended up using a metal file to smooth off the rust in order to install the new pump. With a bit of coaxing, I was able to install the new pump, re-attach the hoses and re-assemble the machine. It works like a charm now. No more leaking! Yeah!

Turned machine on it’s back after removing the hose that goes to the drain, removed the bottom dust guard, I removed the hoses (take a picture before removing things so you know how to orient them when putting it back together) and drained the water first but this is not necessary (there are YouTube videos where they suggest removing the outer case, unclipping the pump and then removing the motor. This would be optimal as you don't need to deal with the water running out of the washer when you remove the hoses). Removed the 4 electrical connectors (multi-plug, 1 x two prong plug and 2 capacitor connector plugs) One of the motor hangers were broken on my machine, I removed the other one and then slipped the motor out. Removed the broken hanger and securing screws and the old rubber grommets, slipped the coupling out (had to leverage out with a large flat screwdriver). Installed new coupling and rubber on the gearbox side, 4 grommets on the motor and the other coupling on the motor. Inserted the hangers on the gearbox side and then mounted the motor. (it is easier if you turn the washer on its back so the drum moves down and gives you more room to drop the motor in from the top), clipped the motor hangers on and fastened the two metal screws, mounted the pump and hoses and reinstalled the dust guard. Turned it right side up and tested before dragging it back into the laundry. Washing again like it did when first bought it in 1998. I would recommend that when a coupling brakes, replace it as well as the hangers and grommets to make sure it has no room for play. Mine broke way too quick as I did the last coupling about a year ago, problem I think was that I had the wrong grommets causing excessive vibration and wear.

I followed the instructions on youtube and replaced the drain pump. It was so easy!!! I am so proud of myself and so is my husband! I took off the cover and simply replaced the drain pump. I am such a stud! :)

I followed the instructions on the video. One difference with the Kenmore model is that the screws were in front instead of the rear of the machine. Still had to pull the machine out to get to the rear to replace the valve. All went smoothly and the unit works like new. Now it takes less then half the time to do laundry. Great parts and timely delivery. Excellent instructional video and instructions. You folks are the best. Thank you.

Started to replace the water pump but looked online at Youtube and everyone said to look at the lid switch first. I bypassed the switch and sure enough that was it! No need for the pump.