11022692100 Kenmore Washer - Instructions

Removed the agitator and the broken directional cogs. Ordered the new ones; recieved them within a couple of days. Replaced the cogs; in no time the washer was working like new.

I followed the video clip that showed how to make the repair that was attached to the email sent from Patrselect notifying me that my part had been shipped. The video clip was excellent and no other instructions needed. Thanks

Removed center top cap/sofetner dispenser. Removed center shaft bolt. Pulled off the top agitator section from bottom portion. Inside the upper agitator is the inner housing for the cogs, pushed right out. Remove cog retainer plastic ring. Careful, the cogs freely fall out and it a little tricky when reassembling. Reassemble every (cogs go in only one way), place the upper agitator back down and over lower portion in machine. Now Put the bolt back in place. Here's the tricky part. You will need a magnetic tip driver or socket to hold the bolt until you have it started because it sits in recessed "well" area. I used a dab of regular Elmer's glue from bolt head to socket. Worked like a charm. Be careful not to over tighten bolt. Remember, upper agitator should free spin one direction and "catch" in the apposing direction.

Almost identical to the instruction video that was sent. Very straight forward. I did not take apart the washer to identify the problem. I was short on time so I took a chance and ordered the highest probability cause of the symptoms indicated by your website. It was dead on; the problem is fixed. Parts were received ahead of schedule. Excellent all around.

After researching possible failure modes and reviewing a video for teardown/access from the control panel and access top down I noticed a lot of 'break dust' on top of the transmission. Shorting out the lid switch and putting my little finger on the drum, it would not spin but the clutch was spinning fine. I ordered a new clutch... Interesting thing when I was taking the clutch out... the gear it was attached to slid right off! After figuring out it was too big to go 'back' into the transmission and reviewing the parts explosion diagram... it BELONGED INSIDE THE TRANSMISSION! So I took the transmission cover off, poured out out the black-ish oil with metal filings in it, put the gear inside, filled it back up with 10W30, put the lid on, added the new clutch while it was apart and finished reassembly. Wow! It spins much better than when it was new. I guess never assume what can happen on an assembly line. Thanks for the great site.

took motor of 2 screws instaled motor coupling

The training video you supplied was right on. I watched it twice to make sure I understood the procedure. I followed the steps outlined in the video and encountered no surprises. The replacement valve was a perfect match and functioned perfectly after installation. I checked other sources for the price of the replacement part. Your price was more than competative. Thank you for a fine service.

It was really easy, just follow the video. The washer machine sounds like new now.

After alot of helpful advise from you guys I replaced coupling water pump clutch, and the problem was still their. Then I tested motor capacitor and it appears dead. So I should receive new one tomorrow and hopefully success! I turned machine over and oil leak..so that's where the string with hose and air needle come in handy to put 90weight oil in through breather hole in gear case.

don't know, I ordered the part and my husband repaired it. Did not take him long at all.

The repair was fairly simple - the hardest part was taking the shell of the washer off and putting it back on.

Tipped the washer on its side and took the pump off then the motor then the coupling.

Following another tip from this blog, I unscrewed the assembly and let it dangle. Then I used screw nuts to attach the wires. Big tip: Cut off the wires right next to the old assembly and use the smallest wire nuts you can find. It's a little tight, but can be done. The grounding wire is not a factor. Took me 10 minutes. Thank you partselect!

Pulled off the fabric softner holder, pulled out the cover for the agitator. Used a socket set to loosen the screw that holds in the agitator hub, pulled out the hub, removed the gasket from the cogs and replaced new cogs. Works like new!!!!

I purchased the part from PartSelect because it was very reasonable and it was OEM part. I have never replaced this kind of part on a washer so I figured it would take me a while. But PartSelect supplied a video showing the entire repair and that was the only reason I did not struggle with the repair. I will definitely buy any appliance parts I need in the future from PartSelect. Thanks Don