11020954993 Kenmore Washer - Instructions

just like video except to keep cogs in place I inverted upper agitator with all parts and bolt inserted held in place with socket and extension.

Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

I just followed the steps on the video, I was surprised how fast I got the parts within 24 Hrs . Thanks

Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.

The top of the agitator pops out and leaves the fastener(a 17mm bolt) open at the bottom of a 6 inch or so opening in the top piece. That bolt comes out with a socket extension and the top comes off. Replacing the dogs is just a case of sliding a retainer ring down, removing the broken dog pieces and replacing with new dogs. Reverse the disassembly process to reassemble the unit. Now, it works great.

followed the video on the web site and repair was amazingly easy. I have two of these machines, and this same part went bad about 1 1/2 year ago, so this time i was ready for everything. Took everything apart, got rid of old broken part, replaced with new, and Bam, washer back up and running, less than 30 minutes, I am limited on space in my basement, so i didn't turn machine on its back, i did it in the upright position, just utilized some wood blocks to hold the motor during part change, and a hand spring clamp to hold pump and hoses out of my way after removing the clips that hold it on. It's not rocket science, if i can do it so can you. Good luck

Removed softener dispenser from agitator. Removed 1/2" bolt from inside agitator and removed top half of agitator. Removed cog assembly. Used screw driver to pry slip ring up 1/4 " to access directional cogs. Replaced cogs, pushed slip ring back into place. Reassembled agitator in reverse order of disassembly.

First I tipped the washer forward and placed a plastic milk crate under the rear of the washer to support it . Then tipping the washer back. I placed two car jack stands near the front to support and level the machine. Now I had enough room to look under it to see where it was leaking. Right away I could see a drip coming from the pump in the front of the washer. I removed the two water hoses. Then with a screwdriver popped a clip on the top of the pump and one on the bottom. The pump slid easily off . Slide the new pump on and reverse the process

Followed written instructions after viewing repair video. Would have been helpful to know how far onto shaft each drive piece needed to be placed. I should have noted old piece placement, though if this was noted in instructions it would have been reassuring to know what is the proper placement. I also placed machine on its back to align the motor and transmission after new parts were installed on each.

We started to get water hammer in the pipes when ever the washer was set to cold? Looked it up here and figured the inlet was about to go out, ordered the part, 2 days later, brand new washer, no more problems. Local repair would have cost us at least $100.00, part was $25.00 shipped, videos are awesome tools, PartsSelect Rules!!!

Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

The repair was easy and the video tutorial was great. That was the easy part. I also had to replace the drain pan and getting it in and out of the pan is no easy task. Plus when you have not moved the washer in 10 years there is some cleaning to do. I would not hesitate to do it myself again. It cost me $20 and some sweat equity.

Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

I watched the video to get a good idea of the procedure. I followed the instructions to remove the cabinet but kept the washer upright on its base. I left the water feed hoses attached to the wall spigots, but turned them off. The pump was rusted onto the motor shaft so I left it there. I unhooked the pump hoses from the pump so I could remove the pump and motor as a unit. The plastic coupling ends pulled off the motor and gearbox shafts easily. The new coupling ends have metal inserts which are a tight fit on the gearbox and motor shafts. To maintain the original alignment it's important to drive them fully into place. I greased the shafts then tapped the coupling ends on with a hammer and drift. The drift was a metal tube, inside diameter slightly larger than the shafts, but small enough to bear on the metal inserts, not on the plastic. My diagnosis was wrong - the original coupling was in good condition, but the clutch had failed.

Looked at the video instructions on the web site, then noticed my model was slightly different. Switched to YouTube. Searched "Water Inlet Valve Replacement Whirlpool Washer". The repair was faster than advertised (40 minutes total). Less time than waiting for a repair person... Very good delivery service from Part Select. Will buy again!