11020904991 Kenmore Washer - Instructions

watched the video on line showed how to do it took about 45 min no problem

I googled Whirlpool washer and then water valve on my I Pad and it showed me step by step how to fix it. Thanks Partselect for the great service. Jimmy

electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.

Follow instructions in part repair video from part select,but put washer on back first to see if can access area without removing the whole outer cover we did not even need to do that step only took 20 minutes to replace coupling. The video was great

We watched the how to video...repair took less than 15 minutes. You can't go wrong if you just watch the easy to follow video! Washer works as good as new.

Went right by the video, and it worked great thanks

Took apart machine exactly as described in the Direct Drive Motor Coupling Replacement Partselect video. Once I lifted out the motor it was clear that the motor coupling was at least part of the issue because it was in place but broken in pieces. I replaced the 2 plastic couplings and the rubber piece and put the machine back together, as described in the video. Afterwards, the spin cylce worked great, quiet and fast as ever. Very happy I did this myself I'm pretty sure I saved a few hundred bucks vs. a repair tech coming to the house. Note that the new couplings require some tapping in order to sink into place.

used pliers to remove rings on 2 hoses, popped 2 retaining clips off of old pump, put new one on, hooked up hoses, fastened clips and was done!

I watched the how-to video twice and the repair was just like it. My only tip would be to have a pan or floor drain nearby to empty the drain hose prior to tipping the machine on its back.

My son and I leaned the washer backward and I had my son hold it while I got underneath of it and unscrewed the two hose clamps to loosen the hoses, pulled them off. Then I flipped the two clamps holding the pump in place and the pump came right off and it took about 2 minutes. I ran into a little problem putting the new pump on because I wasn't getting the drive shaft lined up quite right, otherwise the whole thing would have only taken about 10 minutes total. As it was I got the pump mounted, repositioned the clamps and then hooked up the hoses...done! The design is perfect for ease of pump replacement; kudos to the engineers who designed it!

move machine away from wall---shut off water and remove hoses--loosen screws that hold valve on back wall---remove toplid, place to side--diconnect water line at tub----disconnect wires to valve,hot/cold---remove old valve with hose attached---take new valve and place new mount bracket on, little tricky did not line up at first must force plate to slid into plastic slot so screw hold lines up, without breaking new valve---once bracket on replaced all---used tape on inlet valves thread when supply hoses replaced--seems shorter than old valve--but tighten up OK no leaks

We followed the instruction from your site on the Internet ( Video-Demo ). Everything was very simple and very easy.Thank you for that , we saved a lot of money .

watching the video was a great help, not a perfect match as mine but enough information to get the job done! parts were cheap & they shipped fast. keep coming with the great videos!

After i pulled the motor off the washer, i found the coupling that was busted,removed it and put on the new one i got from you and just put everything back together again and the machine is operating as good as new again.

watched the repair video on u-tube and followed it. Had trouble separating the top agitator from the bottom agitator after removing it from the washer. I tapped the 4 white tabs on the top with a hammer and screwdriver. Top and bottom separated after that.