Models > 10661992100 > Instructions

10661992100 Kenmore Refrigerator - Instructions

All Instructions for the 10661992100
61 - 75 of 224
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
OLDER Ice Maker on the fritz
Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric
Parts Used:
ICEMAKER
  • Eric S from Boca Raton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Wrench set
6 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Parts Used:
Refrigerator Door Switch
  • Thomas from Roseville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Parts Used:
Refrigerator Door Switch
  • stu from richmond, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clear Dairy Door Broken
It was simply placing the clear $60.00 door in place. It was a very simple fix, but expensive!
Parts Used:
Door Compartment
  • Robert from Hemet, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door shelf brace was missing.
I snapped the two end caps into the shelf rail and pushed it into place on the bottom of the inside door.Tolls were not needed as it was a perfect fit.
Parts Used:
Door Retainer bar - White End Cap Trim Piece
  • Gary from COLUMBUS, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Faulty light socket
Followed the video instructions.
Parts Used:
Light Socket Kit
  • Larry from HOUSTON, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper drawer rail broken at one end
The rail just snapped into place with a light pressure. I worried it would require manipulation or heavy pressure and I would break the end while installing it.
Parts Used:
Crisper Drawer Rail
  • MARTY from GREAT FALLS, MT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket wouldn’t hold door shut.
NO DIRECTIONS CAME WITH GASKET! Project failure as gasket tore on a corner. For the price of this gasket, I was DISAPPOINTED. Door is being held shut with a childproof strap.
Parts Used:
Fresh Food Door Gasket
  • Patti from GARNEILL, MT
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Did not have ice maker
Followed online video instructions
Parts Used:
ICEMAKER
  • Marisa from TEMPE, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
install ice maker with all parts for refridgerator with no ice cube hardware on it.
I followed the directions and it worked.
Parts Used:
ICEMAKER
  • Vincent from THE VILLAGES, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Parts Used:
Bimetal Defrost Thermostat
  • Ted C from DSRT HOT SPGS, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker
My husband is an appliance man and he did the work.
Parts Used:
ICEMAKER
  • Ann from MC CUNE, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Installed a Ice Maker
Very easy to install
Parts Used:
ICEMAKER
  • Don from HOUMA, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Parts Used:
Refrigerator Door Switch
  • anthony from HAVELOCK, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Parts Used:
Capacitor
  • David from MARYLAND HTS, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10661992100
61 - 75 of 224
Back to Top