10656566400 Kenmore Refrigerator - Instructions

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

Followed instructions in video and instructions by other home owners. Installation went very well. Parts Select shipped the repair kit. A good company to do business with. Saved a lot of money by doing the repair myself.

First of all, I am a female. So anyone can do this.I simple watched your video. Made the repair very simple. I was surprised that it really worked. I couldn't understand that if the door would still eject ice, why it wouldn't make the ice. It's the same motor. Anyway, It worked and I thank you very much. Very satisfied.

With brief instuctions it was very sraight forward. Three scews hold the motor assembly on. Ordered on a Sunday and the part was here the following Tues. Thanks Partselect

I changed out the complete ice maker by first un-plugging fridge from the electrical outlet,then taking out the three screws holding the ice maker in place, unplugging electrical connector that operates the module and then removed by sliding ice maker away from fridge. Replaced old ice maker and re-plugged connector. Screwed ice maker back into place and plugged fridge back into outlet. Within 5 minutes we could hear the water dispenser filling the ice maker. Within another hour we had our first batch of ice.

I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

Removed ice bucket so ice would not dispense while working on ice guide. Removed damaged ice guide by prying 2 clips with a flat-head screw driver. Installed new ice guide by pushing beyond final position, lower bottom clip into position, then snap 2 side clips into place.

I emepted the drawer slide it out and replaced it with new drawer . Then I filled the drawer back with food i had removed. The cap was easy. I just removed the old one and replaced it with the new one.

Extremely simple especially after watching the video. Makes me think about why I did not attempt my own appliance repairs in the past. Big time savings! Thanks. P. S. excellent delivery service from Parts Select.

replaceed control motor assembly 3 screws took it off. then turned ice maker shaft by hand to line up key slot on new control unit . slid right together .ice started making within an hour . and the part got to my house the very next day after ordering awesome...

I watched the video so I had an idea of what to do. It was pretty straightforward. Turn off the water, take out the screws, line everything up, replace the part. It went smoothly and the icemaker is working again. :)

Unscrewed three screws, inserted new part, completed in less than 10 minutes and my icemaker works!!!! My icemaker did not work for 2 years and after spending $58, my icemaker was back in action.

The part arrived very quickly. I set up the laptop computer on the counter and started the instruction video (THEY ARE THE BEST!). With just a few starts and stops of the video during the installation in less than 15 minutes the repair was complete! The next day I had more ice than I needed. What a fabulous way to make appliance repairs at minimal cost! I will ALWAYS use PartSelect for any future repairs. I should also tell you that a 70 year old Woman did this repair - easily! If I can do it so can you!!

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Replaced Ice maker unit