10656542400 Kenmore Refrigerator - Instructions

i talked to a gentlman name Ruben and directed me to the parts i needed i ordered them and put them by myself i ended up saving over 200.00 dollars thanks to Select parts the minute i finished the process and closed the freezer doors i could hear the ice is comin down again it was good feeling. After i changed the emitter and the receiver this year every thing is working again

Wash, dry, insert.

No prior experience in appliance repair. The majority of time was used in researching the problem and how to fix it. The Parts-Select website and the comments of prior customers made it easy to diagnose and repair. Unplugged the unit, popped of the ice maker cover to get it out of the way, unscrewed the plate covers for the emitter and receiver, changed them out, replaced the covers, replaced ice maker cover, plugged in. Moved on to the next problem.

No prior experience in appliance repair. The majority of time was used in researching the problem and how to fix it. The Parts-Select website and the comments of prior customers made it easy to diagnose and repair. Unplugged the unit, took off the cardboard back cover, located the start device, using website comments and information pried it off, placed the new one, put cover back on, plugged in. By morning back to 40 degrees. Took apart the old one out of curiosity and it was completely burned-up on the inside.

watched video and did same thing,works great now,ordered parts friday morning arived saturday,very pleased!

The Crisper Pan ordered through PartSelect was a perfect replacement. The item ordered arrived quicker than expected. I'm very pleased with your service.

1. Turn off ice maker and cut power to refrigerator. 2. Remove food from top two freezer shelves and remove top shelf. 3. Using nut driver, remove screw that secures plastic shield to the bottom of ice maker. Remove shield and place it on the empty freezer shelf. 4. Remove ice maker unit by sliding it free of the two rails that hold the bottom of the unit in place ... when it is free of the rails, pivot the left-hand end of the unit downward to allow access to the electrical connection. 5. To pull the electrical connector apart, use a small flat-end screwdriver to pry (gently) just above the little protrusion that keeps the two halves secure during operation. 6. Once the electrical connector has been pulled apart, the unit can be placed on a counter top. Pull the square plastic shield off the left-hand side of the unit (it just pulls off, no screws hold it in place) and set it aside on the counter. 7. Remove the 3 screws that hold the motor assembly in place with a phillip's screw driver. Pull off the motor assembly and push on the new motor assembly ... you might have to "wiggle" the white plastic "fingers" over the ice bin to get the axle aligned properly with the motor assembly ... this is very easy to do. 8. Screw new motor assembly in place. 9. Holding the ice maker at an angle in the freezer, reconnect the electrical connectors, then hold the ice maker level in front of the side rails and push it back in place. Replace the small shield and secure it with the screw and nut driver. Replace freezer shelf and food, restore power to the refrigerator, turn on ice maker switch. Wait a few moments and hear the blessed sound of water filling the ice maker tray. Put away tools, check time (a 10-minute job!), do victory dance ... and then see the shield that covers the motor assembly still sitting on the counter! Repeat process, except this time it is not necessary to take apart the electrical connection ... but, of course, the ice maker now has water in it so when you tip it to push the shield back on ... Suffice it to say, that even though I had to do the job twice, I was thrilled with my $59.00 part ... we live in the boonies so a service call by a repairperson would have cost me more than $200.00 ... plus the part and labor. Blessings upon PartSelect!!!!

I did the repair, but apparently there's an Ice Door Kit with Bracket ( Part #8201756 - PartSelect Number PS990120 ) that has a metal bracket that will actually fix the problem with the broken plastic that holds the pin in.

Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

Ordered new glass shelf installed it.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Took the part out of the package and installed it. The service I received was excelent. Got the part two days after ordering it

as shown in instructions