10655606400 Kenmore Refrigerator - Instructions

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Greatest thing about this company was properly describing in an easy clear manner along with the video. A picture is worth a thousand words. A video is worth? Disconnecting wires in back of freezer was a little hard. I didn't know you would have to wait for a complete cycle before the water would fill and make the first batch of ice. I thought it was not hooked up properly and took it back apart. This time I left it, waited and in a few hours, it started making the first batch of ice. Great company, price and fast shipping. Would definitely buy from again

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

Followed the video supplied with shipment info from parts select. Simile and a great way to help the diy person. I will reyurn as a customer as well as pass the word. Thanks jhg

With the new Ice Guide all I had to do was a use a small screw driver to help guide the tabs into place and I was finished!

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

replaced the valve

Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Put in new motot and control

Hi, this was an easy repair job. And, after I was done I felt like McGyver. It took me about 1 hour. The hardest part was getting ice maker's power source disconnected. That was tricky; you have to remove the housing that covers the power connector.

I rearranged the other bins on my refrigerator door. I checked the space between the bins, to make sure I could remove and insert items easily. I put my new bin in place, I made sure it was secure and I put taller items in the new bin.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

Removed 3 screws pulled out the old part and replaced it with the new one. Then plugged in the refrigerator and the repair was complete.

i followed instructions on video it went real simple except for the small area to work in.

Remove all items from door. Remove bolt holding plastic cover on top hinge. Support door and remove 3 bolts holding hinge. Lift door off lower hinge pin. Remove bolt holding both cam assy's and pry the one on the door out with the screwdriver. Replace both with the new cams, place door on lower hinge pin, place upper hinge pin into door, loosely insert the 3 bolts. Align the door, tighten the 3 bolts and replace plastic cap/bolt. Put the food back in the door and you're done. The only nut-driver needed is 5/16" and the screwdriver is only needed to pry out the cam that's located on the door itself.