Models > 10654582400 > Instructions

10654582400 Kenmore Refrigerator - Instructions

All installation instructions for 10654582400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654582400
1,366-1,380 of 1,525
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water wouldnt come out

  • Customer: rebecca from burlington NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
take nutdriver remove back cover, remove screws holding valve, unhook lines, hook lines to new valve, reattach valve and bracket and cover . yhats it!

Ice maker was not producing ice.

  • Customer: Kenneth from Lafayette LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I removed the old water inlet valve and replaced it with a new one. I had to cut the existing water lines with a razor to fit the new design of the new inlet valve. I also had to remove the inlet water valve and attach it to the new one. It was real easy once I reviewed the U tube video on how to replace the valve.

Found that the water fill tube from from the water line was frozen

  • Customer: Jody from Cuyahoga Falls OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
from the back of the freezer unscrewed the water feed to the feed tube. unscrewed the tube from the freezer and removed it. Ran hot water through the fill tube and then reinstalled the tube back into the freezer. Cycled the ice maker and the water started filling the icemaker. Did not use the water inlet valve that I ordered. Matter of fact.. I returned it. Always remember to check the fill tube and make sure it is not frozen.

was liquing water where enter line for ice maker

  • Customer: Robert from Hialeah FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
was really ease remove three scwes fron back panel plus two more screws from the water valve

leaking

  • Customer: Steve from Coon Rapids IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
replaced the valve

Garage refrigerator. Vauvle froze and ruptured.

  • Customer: Thomas from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.

Water freezing and creating plug in rubber hose going to ice maker

  • Customer: Matthew from Stanley VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed water inlet support bracket,placed new inlet valve next to old valve with same orientation.one by one disconnected water lines and power leads and reconnected to same position on new valve.Reattached bracket and job done..Access to valve very easy.

Water kept dripping out of water dispenser

  • Customer: Benjamin from Glens falls NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplug appliance, turn off water supply valve to fridge. Remove rear cover and locate water inlet valve on lower right corner. Remove 2 screws holding valve in place. Pay attention to water line locations. Unplug 2 connections on valve. They are different size so you can't put them back on wrong. Remove all lines from bad valve. Cut all ends off lines and insert into new valve. Make sure they go where they belong. Press firmly into place. Reconnect electrical plugs and screw valve back in place. Turn water supply valve back on and check for leaks. If all is good put rear cover back on , plug appliance back in and your work is done. Easy replacement job.

Leaky water dispenser

  • Customer: Robert from Doylestown PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the video and was done with the replacement in less than 20 minutes. Just make sure after turning the water back on you check for leaks before you move the refrigerator back.

ice cube maker fill tube leaking also not dispensing ice

  • Customer: Dean from Hacienda Heights CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Followed instructions- removed and replaced with new water inlet valve also replaced control bracket. Now no leaks and plenty of ice thanks to partselect, the right part, the right price and fast delivery . Thank you

water dispenser leaking, auto ice maker froze up

  • Customer: John from Lincoln NE
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Researched in "ehow" the procedure. Looked relatively simple so I ordered the part. When it arrived, emptied the frig, pulled it out, thawed out the auto ice maker with a hair dryer. I then examined the old part and compared it to the new part. They were close. Old part had a rivet attaching it to another bracket which had a primary valve that led to the filter cartridge housing. I had to drill out the rivet to seperate the mounting brackets. The electrical connectors were rear facing on the old unit and front facing on the new unit. Not a big problem, just concerned that the solenoid leads might be polarity specific. I called my brother who works on restaurant equipment and he said that as long as the long were the same color, polarity was not an issue. He was right. The second concern I had was that the plastic line from the primary input valve was a stiffer gray plastic line with a rib molded on the ended to secure a metal compression nut. I wondered again if that would cause a problem with the new pressure connector. It did not. Just cut off the rid and slide it in. Frig is working great, dispensing water and ice like it was new. Bought the frig for $1,000 13 years ago, now sells for $2,500. Save a ton of money by buying the part and doing it myself. Thanks.

Ice maker not working

  • Customer: Greg from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.

My ice maker quit working

  • Customer: pauline from somerville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have some electronics background but your listed problems helped me narrow down the problem. I ordered the part, removed old part, installed new part (maybe 15 minutes total) and my icemaker started dumping the ice that was in the tray within 20 minutes and making more. That clunking sound of ice was music to me ears and wallet!! Thanks!!

Ice maker wasn't getting water

  • Customer: Anna from Morgan Hill CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called a repair man out to see what the problem was because my husband just died and I didn't want to pay such high prices for a repair. He told me I needed a new motor for the ice maker and it would be a total of about 305.00. I couldn't believe the price. It cost me 59.99 for his diagnosis. I went to your web site and found the part and watched you installation video. I am 65 years old and I was able to install the new part in less than 15 min. The part was about 95.00. I saved 150.00 by doing it myself. I will always look on line before I have a repair man do a job. I may need them to diagnose the problem, but I will try myself before paying such outrageous fees.

Ice maker not making ice.

  • Customer: Lewis from Roseburg OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the trouble shooting & installation videos , Checked to make sure water was getting to the door.I look'ed closely at the entire unit. every thing seem'ed to be OK. I made a guess as to which part to order. The control motor or the thermostat. The control motor made more sense to me. I made the right guess. works like new.
All Instructions for the 10654582400
1,366-1,380 of 1,525