Models > 10654536400 > Instructions

10654536400 Kenmore Refrigerator - Instructions

All installation instructions for 10654536400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10654536400
1,456-1,470 of 1,607
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

old ice maker did not work at all.

  • Customer: Donavan from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator and turn water supple off. Remove three mounting mounting screws and unplug the old ice maker.(there is a latch on the plug to release it) Remove shutoff arm from old unit or if ordered seperatly with the ice maker, install shutoff arm on the new unit. Plug the new unit in (latch will snap into place when plug is properly seated.) Install the bottom screw (leave screws loose until all are started in the orginal holes). Tighten screws and you are done. Turn the water on and plug refrigerator in. After about an hour or two the ice maker will be cold enough to start making ice. In about five hours or so you will see the first ice cubes!!!!

plastic stopper came off arm

  • Customer: TinTina from Bruce WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
with a mirror to see the small hole on the front side of the icemaker.... very simple, took 1 minute

Fridge and freezer not coming on without coaxing.

  • Customer: Howard from Victoria TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Been fighting this for over a year. Sometimes the fridge and freezer would heat up past the point it should come on. Had to slide the fridge temp control back and forth until the unit came on. Researched the problem determined the thermostat to be the issue. Got the part, finally found the time, then took the top tray out, popped off the escutcheon, unplug some wire and took out the control shuttle. Removed the old and replace with the new thermostat. Re-installed everything, plugged in it in and BAM. It's working. Now just fine tuning the slides to desired temps. THANKS PARTSELECT.

Refrigerator and freezer stopped cooling.

  • Customer: Jonathan from Puyallup WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Went to the site to determine the problem and ordered the three most probable causes to my situation. replaced two of the items and had to send one part back because it didn't exist on my Model. Still did not run. Went back to the site and ordered the thermostat and the problem is resolved.

Our 6 year old refrigerator stopped keeping food cold

  • Customer: Kenneth from Muldrow OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It was pretty simple. I watched a few videos on youtube. Diagnosed the problem. Ordered the part from PartSelect. It arrived a few days later. Followed the online directions for replacing the thermostat. Voila!!! We have a working refrigerator again!!! I'll NEVER call a repair man again. Thank you PartSelect!!!

refrigerator too cold

  • Customer: mike from ROSCOE IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
unplug the refrigerator, remove all the items on top shelf, remove the face plate with small screw driver, pry only at the top; remove the screw for the trough and the screw on the louver housing the remove these parts; remove the face plate with small screw driver, pry only at the top and remove;use a 1/4 nut driver and remove the 2 screws in the rear top and the 2 in the front of the panel then unplug the connector at the top left by squeezing the tabs, at this point take 2 pieces of wire and put in the front screw holes to let the control assembly hang down about 4 inches, this will be adequate to prevent damage to the louver linkage assembly; then reach in to the styrofoam louver housing and remove the section of thermostat bulb tube , it is held on by 6 clips, and release the 2 clips inside the control housing to free the sensor tube on the old thermostat, remove the 2 small screws that hold the thermostat with a short phillips screw driver , pull out slightly and remove the 3 wires with needle nose plyers, noting the colors, at this point the thermostat is completly free; straiten the old thermostat tube out for easy removal of the plastic tube, staighten the new tube for easy installation of the tube noting that the bulb is about 1/2/inch from the end of the end of the tube at this point instalation is reverse of removal , be carefull not to put any sharp bends in the tube upon installation or this may damage the effectivness of operation.

Absolutely incredible to purchase replacement Parts at Part Select.

  • Customer: Gary from Highlands Ranch CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Absolutely incredible to purchase replacement Parts at Part Select.

I tried Sears Internet for simple replacement parts per descriptions. They sent me wrong parts that were not even close to requested order. Sears delivered wrong parts and difficulty in returning their wrong parts.

However, our next order at Shop PartSelect.com parts were sent exactly as described on website. This company is incredible as with photos of needed parts were delivered and perfect replacement.

Suggestion is DO NOT ORDER FROM SEARS REPLACEMENTS.

Shop PartSelect.com

They have the best price know parts desired.

Thanks
Gary

Refrigerator and Freezer very warm food spoiling

  • Customer: Melba from La Habra CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Went online and found troubleshooting steps for this particular make, model, issue and ordered the parts recommended. Unplugged the refrigerator and removed the screws from the back panel and located the parts easily by using the instructions with pictures provided with the parts. The parts simply popped out without tools and popped back into place. Replaced the back panel and plugged in the refrigerator. Works like new.

Fan and lights work; compressor wouldn't come on; refrigerator and freezer would not cool down

  • Customer: John from Mt. Pleasant SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Instructions were great, and all parts included for both compressor options. Once I figured out which parts to use, it took only minutes to repair; straight plug in; no problem or modifications required. Old control device innards were rattling/shot from the move. Best $50.00 I ever spent! Milton Waddams, Mt. Pleasant, SC

REFRIDGERATOR NOT COOLING AND FREEZER NOT FREEZING

  • Customer: MARK from MEDINA NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
TOOK CARDBOARD BACK PANEL OFF AND LOOKED AT COMPRESSOR NUMBER AND FOUND RIGHT PART NUMBER FROM THE COMPRESSOR START KIT. IT WAS SOMEWHAT CONFUSING AS YOU HAVE TO TAKE THAT PART OF EXISTING UNIT. THE RUN CAPACITOR IS DIFFERENT SIZE BUT WORKED. WORTH THE TROUBLE FIGURING OUT INSTRUCTIONS FOR PARTS BUT IS WORKING GREAT RIGHT NOW.

Side by side fridge freezer not cooling

  • Customer: Alan from Lawrence KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed rear lower panel. Checked compressor start device and noticed it was burnt out. Ordered replacement, 2 day delivery, identified correct type re compressor model and plugged it in. Replaced rear panel, switched on and hey presto all cooling and working great. Could not have been easier. Great service!!

Refrigerator would not cool.

  • Customer: Bruce R from Beaufort NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Did some research on internet. Order part. Replaced part. New problem now. After running about 15 hours, the ground fault circuit gets out. And again the refgrigerator stops working. Reset ground fault circuit and after about 15 mins. it starts working again. Not sure what is causing the problem now. Anybody have any suggestions?

Freezer not freezing food

  • Customer: conrad from LaPlace LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
remove power. Remove rear cardboard panel.. Remove wiring from startup kit. Remove defective startupup kit. Then reverse procedure.

overloads melted

  • Customer: albert from westwego LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
installed o/l unit which was #1 on instruction sheet ,very easy, pluged side by side refrigerator freezer in ac outlet, checked amps on compressor, and a very happy ending! THANKS!

Both fans running/No cooling/Compressor hot & Not running

  • Customer: Jeff from Belfair WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I checked the compressor, very hot to the touch & not running. I unplugged for a few minutes to cool & when I plugged it back in, it started for maybe a second or two. Then I unplugged the relay from the compressor and new instantly it was fried. So I decided to google the issue which led me too partselect.com and I then realized this relay is called the start device/Relay and it also provides overload protection for the compressor. When I received the part or parts in this case, they came in a small box which included 2 combo relays, 2 overloads, 1 ptc start relay, 1 jumper wire, 1 electrical cover, 1 instruction sheet. By using the number on the compressor I was able to see that I needed to use the ptc start relay & one of the 2 overloads which plug onto the compressor & I needed to use the white jumper wire as the terminals were a different size on the ptc relay. At first I was a little confused because I unplugged one relay and the replacement was two separate parts. Had to read instructions carefully several times to make sure I was using the correct overload and ptc relay. I plugged in the fridge to test & it worked great so I unplugged and installed the electrical cover, reinstalled cardboard cover on back of fridge & I was done. Two weeks later fridge is working great!! Hope this helps.
All Instructions for the 10654536400
1,456-1,470 of 1,607