10653232300 Kenmore Refrigerator - Instructions

That was soooooooooo easy. Thanks for a really wonderful website. Part was simple to find and shipped extremely fast.

It was pretty easy, but I sure wish they had said the auger had "left" hand thread. After I watched a vid on youtube the job went very easy. The new auger works just fine. The only problem I had was the left handed thread with the plastic nut on the end of the auger. Well worth the effort now I can get ice reguulary.,All the parts fit too.

Ordered part from Parts Select at half the cost of other listing on www. Took 5 minutes and shelf fit perfectly.Thanks.Mike

easy slid in of new drawer

Removed the auger apparatus from the ice bin, replaced the auger drum and then reattached the auger apparatus to the bin. Cause of breakage was due to ice melting in the bin and then refreezing. Keeping the many parts in the correct order on the auger can be difficult.

Instead of trouble shooting what part was bad, just replaced the whole unit. Probably cheaper in the long run and the whole process took less than 15 minutes. Pulled the old icemaker out, plugged in the new one and back in business.

The video of the repair that was on your website was extremely helpful. It showed in detail how to replace the parts item by item. I could not have done it correctly without the video. I believe anyone could have replaced these parts with your instruction video.

Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

My wife could have made the repair, I got on line, typed the problem in and PartSelect came up. The drawings were there as well as instructions. The part came, again with instructions and it took about 20 min. Good job guys.

Shut off water & electric.Remove 2 screws,cut water lines,unplug electric plug. Install electric plug,push water lines in.reinstall screws,hook up water line & plug in ref.Turn water on, ck for leaks.

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

Pull out the refridgerator from the wall. Unplug the fridge and turn off water supply. Remove the cardboard cover from the bottom of the back side of the fridge. The valve assembly is on the bottom right side of the the fridge when looking at the back. Remove the valve assembly. remove the color coded electrical connectors. Push in the quick disconnect fitting on the valves and gently pull the tubes out of each valve, if it won't come out you can cut the lines, just make sure they are nice and clean and straight. The new part was a perfect fit. Push the tubing in to the size matched valve inlets reconnect the electrical connections reattach valve assembly to the fridge, next open the freezer door and lift the ice make door and take you a hair dryer,turn it on and hold it about 1-2 inches away from the rubber hose that is used to fill the ice maker for about 2-3 minutes to remove the ice blockage. Once it is clear, turn on the water check for leaks and verify correct operation of water and ice. Reinstall the card board, push the fridge back into place. and enjoy a cool beverage and pat your self on the back cause you just fixed your ice maker!

determend o.k. water flow,determend solenoids o.k.problem had to be ice maker.ordered part on Su. eve.,recieved new part Tue.A.M.,had part installed in 15 minutes. Then waited for quite a long time untill it finally made ice.