10652512100 Kenmore Refrigerator - Instructions

I did the repair just as your video showed me. It worked out great.

installed ice maker control & motor assembly

Very simple. Using only a screw driver removed all the screws and removed the front part of the ice bin. Then I removed the screw auger that pushes the ice out and reassembled every thing to the new ice bin.

Removal of escutcheon was easy. Replacing icedoor was fairly easy, working with wires in the way was a little distracting but simple. Be careful with microswitches and locating pins. Two of mine broke, had to replace bracket. Simple job again. Everything working fine now. No ice jam in chute. Using needlenose pliers to remove/insert pin is the best and easiest option.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

The most difficult part was after I removed the old Start Device kit, the electrical wire clamp had to be adjusted so that it would fit back on the new compressor start device. Also the new one did not look like the old one so it took a few minutes to read the instructions and set it back up correctly but once in place it worked like a charm.

I followed the instructions shown in the on-line video for replacing the thermostate control. I had difficulty freeing the capilary tube from around the mechanical lever that controls the freezer side vent opening. I had to remove a screw that held the vent lever in place. This is a delicate activity. I was not happy with the way the on-line video delt with this particular issue. Otherwise, the video was right on and straight forward. The problem is fixed.

Lower door closing cam was completely worn down so door wouldn't close on it's own. Ordered parts which arrived in a couple of days. After watching installation video on this website the job looked pretty easy. Needed socket wrench to loosen nuts at top, they were really tight. Removed door. Replaced both the cam on the bottom of door and the cam on the main unit, put door back on making sure it was straight and lined up properly. Retightened top nuts securely. Voila, problem fixed in only about 15 minutes or so.

I followed the instructions on the repair video, fridge is working fine now. Thanks!

I just wanted to tell about the good service they gave to me. The first one I received was broken, and with one phone call they sent me another, no problem. Installation was take the broken one out and replace it with the new one.

Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

If you are having this problem, read this. My refrigerator door would not stay closed. This was over a year and a half time period. I thought it was something complicated and told my wife to call a repairman. Thank goodness she does what she does best - not listening to me! I finally had enough and went online and googled my problem and found PartsSelect. PartSelect had a repair video showing how to fix the problem. If you are like me, I'm very cautious about purchasing from a website in which I'm not familiar. PartsSelect is a reputable site (I promise I do not work for them). My refrigerator is over 8 years old and they had the part I needed, a lower door cam, along with a video on how to install the part. This honestly took about 5-10 minutes to do and I did it without any help. I was so aggravated at myself for waiting so long at doing this!! I actually ordered 2 of these parts, just for the next time. You can do this.

Pulled out the icemaker. Switched out the Motor Assembly (so easy) and woke up the next morning with ice. Our ice dispenser wasn't working either. This repair inspired me to take the ice dispenser apart and I found that the lever arm wasn't touching the contact when pressed. We now have ice and a working ice despenser. Oh yeah--my wife was so impressed. The part came in on time and it was very very easy to replace.

Once we figured how to get front off, it was like a puzzle. One piece at a time. So thankful part has been improved and replaced. It works better than before, just wish would have done it sooner.

Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.