10652282202 Kenmore Refrigerator - Instructions

Took augur off broken bend put augur in new bend took 10 min now I can have ice. shipping was super fast.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

replaced the valve

Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Put in new motot and control

Replace the auger drum. I had order it and the auger, but I did not need the auger. I returned the auger with ease. Parts Select will always have my business.

The plastic control bracket would not "lock" in place because the plastic detentes broke, not allowing the ice maker dispensing 'paddle' to engage the micro switches that allows the ice maker to eject ice. An easy repair of replacing the entire plastic control bracket.

repair went good .only had problem removing tube from clip in front

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

Removed 3 screws pulled out the old part and replaced it with the new one. Then plugged in the refrigerator and the repair was complete.

With the flat screwdrivers, table knife or something to pull the front cover, is not easy but it will come out, patient and kepp trying until you made it, the rest is easy.

It was a no brainer just snap the piece on. The Parts select service is great have bought parts here before and prompt delivery great place to get parts

The video on the site made the repair extremely easy. It took 15 - 30 minutes start to finish. Had it not been for the video I wouldn't have known that the plastic nut on the end of the auger was reverse threaded. I would highly recommend this site for ordering appliance parts.

Took old drawer out, put new drawer in. When I first opened the new drawer I was a little disappointed as the printing on the edge of the crisper (where it says humidity low-high) was a different color than my existing drawer, I know it's such a small detail that nobody would notice but me. My fridge is almost brand new and I'm the one who broke the drawer so I was a little sad but then realized that I could remove the edge of the drawer and replace it with my old one... VIOLA brand new drawer with purple letters! The drawer itself came so fast, I believe it was 1-2 days to my door! Thank you Part Select

I would not have attempted the repairs without your instruction. I use a Drimel tool with a abravise blade to cut the part off the shaft. After I realized the Drimel tool would work. It took me parhaps 10 minutes to get it off the shaft. I had already ordered the new part and the job was complete. Thanks for the help. Ron Burch