10652282201 Kenmore Refrigerator - Instructions

Went online and found troubleshooting steps for this particular make, model, issue and ordered the parts recommended. Unplugged the refrigerator and removed the screws from the back panel and located the parts easily by using the instructions with pictures provided with the parts. The parts simply popped out without tools and popped back into place. Replaced the back panel and plugged in the refrigerator. Works like new.

Your web site was great. There was a short step by step video on how to remove and replace the ice door kit and tools required. The only additional tool I used was Blue Tape so I could stabilize the inner control panel out of way onto Door.If I need more appliance parts I now know where I am ordering from!!

Neither the OEM instructions nor any of the PartSelect videos explained BOTH ends of the tube for my particular appliance. All very thoroughly covered the obvious connection with the water valve from the wall. However, the push valve end for my KitchenAid is supposed to insert into the water filter chassis, which can barely be seen from the back of the appliance, much less reached with any tool. In order to make the repair, one must either remove the water filter chassis (which I attempted unsuccessfully), or put the appliance up on jacks in order to reach the push valve site.

I watched the short video at this website about replacing the bracket first. Then I replaced mine. Everything went smooth. No problems. Try it yourself.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Took cardboard back panel off and looked at compressor number and found right part number from the compressor start kit. It was somewhat confusing as you have to take that part of existing unit. The run capacitor is different size but worked. Worth the trouble figuring out instructions for parts but is working great right now.

Greatest thing about this company was properly describing in an easy clear manner along with the video. A picture is worth a thousand words. A video is worth? Disconnecting wires in back of freezer was a little hard. I didn't know you would have to wait for a complete cycle before the water would fill and make the first batch of ice. I thought it was not hooked up properly and took it back apart. This time I left it, waited and in a few hours, it started making the first batch of ice. Great company, price and fast shipping. Would definitely buy from again

Removed rear lower panel. Checked compressor start device and noticed it was burnt out. Ordered replacement, 2 day delivery, identified correct type re compressor model and plugged it in. Replaced rear panel, switched on and hey presto all cooling and working great. Could not have been easier. Great service!!

While removing the old Ice Maker, by looking at the new one, I observed that the old one had Ice frozen in the path of the water flow. After I removed the ice, using a hair dryer, I reassembled the old part and it has worked fine ever since. I have a spare Ice Maker now.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

Followed the video supplied with shipment info from parts select. Simile and a great way to help the diy person. I will reyurn as a customer as well as pass the word. Thanks jhg

With the new Ice Guide all I had to do was a use a small screw driver to help guide the tabs into place and I was finished!

Took augur off broken bend put augur in new bend took 10 min now I can have ice. shipping was super fast.

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

replaced the valve