10652214103 Kenmore Refrigerator - Instructions

easy slid in of new drawer

Removed the auger apparatus from the ice bin, replaced the auger drum and then reattached the auger apparatus to the bin. Cause of breakage was due to ice melting in the bin and then refreezing. Keeping the many parts in the correct order on the auger can be difficult.

The video of the repair that was on your website was extremely helpful. It showed in detail how to replace the parts item by item. I could not have done it correctly without the video. I believe anyone could have replaced these parts with your instruction video.

Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

According to all the information on the internet diagnosing the problem with my in door ice dispenser, the problem seemed to be with the solenoid which I ordered from PartSelect. However, when I got into the repair, I found the problem was with the electrical switch that activated the ice dispenser. A couple of the plastic studs that hold the switch in place had broken which did not allow the switch to be activated. I replaced the small plastic keeper study with small screws and now the ice dispenser works fine.

Found my unit had stopped making ice. I did 20 min. of search on the internet and found this site. I was going to just buy the whole ice maker unit, but after reading a bit more found that the majority was just the motor assembly. I ordered it, 2 days later it was at my front door. I pulled the ice maker unit out, took off the motor assembly, and low and behold a small whit ppiece of plastic fell out. I replaced the motor assembly re installed the ice maker and in one hour I had ice again. As far as ease to do this job from 1 being hard and 10 being super easy, I would rate this a 10+. If you have this kind of problem, I would not waste your money on a repair man, 150.00 service call, Hell no. 65 bucks and your done. Before your wife can make you a pot of coffee this can be out and back in. I don't want to take money away from the appliance repair men but some repairs can be a DIY project. Nut driver and phillips screw driver is all you need.Hope this helps ya.

Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.

Thanks,

Phillip

I poped the outer cover off... Removed 3 screws and gently pulled the old timer out.... Also pulled out the ice maker arm.... Aligned the shaft of the tral to match the new motor assembly and gently slid it in... tightened the 3 screws and aligned the wire hoop back in the hole and the job was done... i pulled out the top freezer basket for easy access... Took less than 20 minutes total..The part was correct as usual.. Thank fellas

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

Ordered new glass shelf installed it.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

as shown in instructions